Kenmore Washer 110.91564110 (11091564110, 110 91564110) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP389387
This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.
- Transfers oscillating motion from the transmission to the agitator
- Provides the splined interface that engages the agitator/coupler
- Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
- Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator
What's included: 1 agitator drive shaft Install notes:
- Disconnect power and water; use proper PPE
- Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
- Keep gears, spacers, and clips in order; reassemble in the original orientation
- Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn
Do-It-Yourself Stories from Customers like You
Agitator was not turning Edward M. • Glen Allen , VA • March 10, 2019
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time.
Read more
More
$116.95
- Compare At:
-
$141.04
- You Save:
-
$24.09
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62889
Used for lid switch.
Do-It-Yourself Stories from Customers like You
Washer was "dead" with a partially washed load and would not do anything Jimmy M. • Hopewell , VA • September 19, 2014
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!)
Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts...
Read more
More
$16.77
- Compare At:
-
$19.79
- You Save:
-
$3.02
Genuine Whirlpool part
By: Whirlpool
Part Number: W11033823
This wire retaining ring secures the door boot (bellow) to the front tub on front-load washers. It keeps the gasket seated to maintain a watertight seal, helping prevent leaks when the washer fills, agitates, and spins.
- Secures the door boot/gasket to the outer tub opening
- Maintains a watertight seal during wash and spin cycles
- Helps prevent the boot from slipping off the tub lip
- Common symptoms: water leaking at the front, a loose or detached boot, or a broken/missing ring
Includes: 1 wire retaining ring Install notes:
- Unplug the washer and shut off water; wear gloves and eye protection—the ring is under spring tension
- Release the outer boot clamp and fold the boot inward to access the inner ring
- Seat the boot evenly on the tub rim, then expand and fit the ring into its groove; verify it's fully seated all the way around
- Reassemble and run a quick test cycle to check for leaks
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.
- Supports and centers the spin basket on the tub centerpost/drive shaft
- Provides a low-friction bearing surface to reduce wear and noise
- Helps maintain basket alignment and stability during spin
- When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin
What's included: 1 centerpost bearing Install notes:
- Disconnect power and water supply before servicing; use proper PPE
- Access typically requires removing the agitator, inner basket, and related drive components
- Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
- Seat the bearing fully and verify smooth basket rotation before reassembly
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3355454
This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.
- Applies tension to prevent rattling and buzzing during use
- Helps keep the mounted piece properly seated and aligned
- Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
- Simple, drop-in replacement where the original clip is used
What's included: 1 anti-rattle clip Install notes:
- Disconnect power to the appliance before servicing
- Note the original clip's orientation; transfer the new clip the same way
- Use needle-nose pliers for placement; avoid over-bending the clip
- The component is secure and clears adjacent parts before reassembly
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3356467
This water level pressure switch senses the tub's fill level through an air hose and signals the washer to start or stop filling and advance the cycle. Replacing a faulty switch restores proper fill levels and reliable cycle timing.
- Monitors water level via an internal pressure diaphragm connected to the tub air hose
- Opens/closes contacts to control the inlet valve and inform the timer/control
- Common symptoms: washer overfills or keeps filling, won't fill, incorrect/erratic water levels
- Cycle may stall at fill or rinse when the switch doesn't detect the proper level
What's included: 1 water level switch Install notes:
- Disconnect power and turn off water before servicing
- Access the console; transfer wires to the new switch one at a time to maintain correct positions
- Inspect and firmly seat the pressure hose; ensure the hose and tub air dome are clear and the hose isn't cracked or kinked
- After installation, run a test fill to verify proper shutoff at the selected level
Do-It-Yourself Stories from Customers like You
Wash machine once in a while would stop running Daniel B. • Leesburg , FL • May 13, 2016
I found that turning the water level switch back and forth would activate the machine So I replaced the water level switch and the plastic hose that connected to it.
I purchased a clamp in the purchase, but it was the wrong size! There wasn't a clamp used in the original set up, so I installed the switch and hose without it! It was the video instructions and having the correct parts that made that made this a easy repair!
Thank You
Read more
More
$101.95
- Compare At:
-
$121.32
- You Save:
-
$19.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: 285666
Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138
Do-It-Yourself Stories from Customers like You
I was replacing the lid switch but decided to install a new vacuum break and drain hose while i was at it Dianne Z. • Manchester , CT • May 27, 2016
Just took off the old vacuum break and put the new one on. It was very easy because the site had a video showing how and I watched it first.
Read more
More
$44.95
- Compare At:
-
$53.49
- You Save:
-
$8.54
Genuine Whirlpool part
By: Whirlpool
Part Number: 285702
Size: 21 inches long. Clamp included.
Do-It-Yourself Stories from Customers like You
Drain hose too short and home depot fix leaked Sara B. • Liberty Hill , TX • August 21, 2015
Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly.
Now we're washing again and no leaks!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP64208
Includes drive tube spacer, "T" bearing and both shaft seals.
Do-It-Yourself Stories from Customers like You
There was a center (tub) shaft seal leak in our Maytag washing machine. John W. • Manvel , TX • June 02, 2021
It was fairly difficult, but I watched and followed the Appliance PartsPros video and was able to get it done using the parts I purchased from APP. The leak has stopped (but I'm still watching after 5 loads).
Read more
More
$142.95
- Compare At:
-
$168.68
- You Save:
-
$25.73
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546461
This brake release cam works with the washer's brake assembly to disengage the brake during spin and re-engage it at stop. Replacing a worn cam restores smooth basket spin and reduces squeal or grinding at spin transitions.
- Disengages the brake so the basket can spin; helps reapply the brake as the cycle ends
- Supports smooth starts and stops of the spin cycle
- Worn or damaged cams can cause no spin or intermittent spin
- Common symptoms include loud squeal/grinding at start/stop or a burning odor near the brake area
What's included: 1 brake release cam Install notes:
- Disconnect power (and water supply, if moving the washer) before service
- Access the brake/basket drive area; the brake spring is under tension—use caution and eye protection
- Note orientation of parts before removal; seat the new cam correctly
- After reassembly, run an empty spin test to verify operation
Do-It-Yourself Stories from Customers like You
No spin every thing else worked made high speed ticking noise Anthony D. • Follansbee , WV • May 12, 2015
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in...
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: 285558
This replacement upper agitator restores the laundry-moving action in compatible top-load washers so clothes get cleaned and rinsed more evenly. It installs on the transmission/drive coupling to re-enable proper agitation. What it does:
- Moves clothes and water during the wash cycle so detergent and water contact fabrics for better cleaning.
- Replaces a cracked, stripped, worn or missing agitator that can cause poor cleaning or uneven loads.
- Helps stop wobbling, banging or unusual noise caused by a loose or damaged agitator.
- Works with the washer's drive coupling/drive block to transfer motor motion into agitation.
What's included: One upper agitator. Install notes:
- Disconnect power and water before starting any repair.
- Remove the agitator cap or fabric softener dispenser, then unbolt/lift the old agitator from the drive coupling per your model instructions.
- Inspect the drive block/agitator dogs and splines for wear; replace those parts if they are damaged to ensure proper operation.
- After installation, run a short test cycle to confirm secure fit and normal agitation.
Compatibility note: Enter the model number into the OEM parts lookup or the retailer's compatibility tool before ordering.
Do-It-Yourself Stories from Customers like You
The two sections of my agitator kept separating & a new screw wasn't the answer but Ann S. • Washington , DC • April 20, 2017
When the drum finally started to list during washings, I knew I couldn't keep screwing the two parts of the agitator together as a temporary fix anymore so I called a technician who promptly and erroneously told me that the entire unit would need to be replaced. This didn't seem right so I checked online and found APP. I'm very thankful I did. The videos, instructions, and parts made the repair possible. With my uncle's elbow grease (taking the old agitator out was no picnic), we were able to...
Read more
More
$150.33
- Compare At:
-
$178.89
- You Save:
-
$28.56
Genuine Whirlpool part
By: Whirlpool
Part Number: WP54583
Right hand side. For screws use WPW10119828.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$19.50
- Compare At:
-
$23.20
- You Save:
-
$3.70