Kenmore Washer Dryer Combo 110.97842700 (11097842700, 110 97842700) Parts

This replacement dispenser stores your dishwasher's detergent and rinse aid, then releases them at the proper time in the cycle. Restore consistent cleaning performance and help prevent leaks around the dispenser area with a fresh assembly. What it does

• Holds detergent and rinse aid; times their release during the wash cycle
• Seals to the inner door to help prevent leaks from the dispenser opening
• Common symptoms: detergent cup won't latch or open, detergent left after cycle, rinse aid not dispensing, leaking around the dispenser, broken latch/cover

• One dispenser assembly

• Disconnect power and water supply before servicing
• Open the door and remove the inner door panel to access the dispenser
• Transfer the wire connector(s); seat the gasket evenly and tighten mounting screws without overtightening
• Reassemble, restore power/water, and run a test cycle to check for proper operation and leaks

This wire retaining ring secures the door boot (bellow) to the front tub on front-load washers. It keeps the gasket seated to maintain a watertight seal, helping prevent leaks when the washer fills, agitates, and spins.

• Secures the door boot/gasket to the outer tub opening
• Maintains a watertight seal during wash and spin cycles
• Helps prevent the boot from slipping off the tub lip
• Common symptoms: water leaking at the front, a loose or detached boot, or a broken/missing ring

• Unplug the washer and shut off water; wear gloves and eye protection—the ring is under spring tension
• Release the outer boot clamp and fold the boot inward to access the inner ring
• Seat the boot evenly on the tub rim, then expand and fit the ring into its groove; verify it's fully seated all the way around
• Reassemble and run a quick test cycle to check for leaks

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

This knob insert is the small piece that snaps into a control knob. It restores a clean, finished look when the original insert is cracked, discolored, loose, or missing.

• Provides the insert for a control knob to replace a worn or missing piece
• Snaps in for a secure, factory-style fit
• Helps keep dust and debris out of the knob cavity
• Typical symptoms: knob center missing, insert cracked, loose, or discolored

• Disconnect power before servicing the control panel
• If needed, pull the knob straight off the shaft to access the insert
• Gently pry out the old insert; avoid metal tools that can mar the finish
• Align tabs and press the new insert flush until it clicks into place

The Lint Screen Door is an OEM part for Whirlpool dryers. It is located at the front of the dryer and provides easy access to the lint screen. It helps to trap lint and debris from the drying process, preventing it from entering the dryer vent and potentially causing clogs or fire hazards.

Causes of a faulty or damaged lint screen door can include regular wear and tear, physical damage, or improper handling. These factors can result in issues such as difficulty in opening or closing the door, a loose or insecure fit, or reduced effectiveness in capturing lint.

Symptoms of a bad lint screen door may include:

• Difficulty in opening or closing the door
• Loose or wobbly door fit
• Lint bypassing the lint screen and accumulating in the dryer vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

Size: 10-16 x 5/8 inch.

Vinyl door seal that forms an airtight barrier around the refrigerator or freezer door to help maintain proper temperature and reduce energy loss. Replaces worn gaskets to stop drafts and minimize frost or moisture build-up. What it does:

• Creates a secure, flexible seal around the door to help keep cold air in and warm air out.
• Helps prevent frost, condensation and uneven cooling inside the compartment.
• Commonly replaced when you see visible cracks, tears, gaps, or feel cold air leaking from the door edges.
• Can improve overall temperature consistency and reduce excessive compressor cycling caused by leaks.

• Remove the old gasket and clean the door frame thoroughly before installing the new seal.
• Warm water or a short exposure to gentle heat can soften a stiff gasket to make installation easier; handle carefully.
• Press the seal fully into the channel and check that it seats evenly around the entire door; avoid forcing or trimming unless specified by the OEM.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

This replacement washer is a small hardware component used in appliance assemblies to provide a stable bearing surface and proper spacing. Replacing a worn or missing washer helps maintain alignment, reduce vibration, and protect mating parts from damage.

• Distributes load under a nut, bolt, pin, or shaft to protect mating surfaces
• Maintains correct spacing and alignment within stacked components
• Helps reduce friction, vibration, and noise in moving assemblies
• Worn or missing washers can contribute to looseness, wobble, rattling, or premature wear

• Disconnect power and shut off gas/water before servicing
• Note the original order and orientation of parts during disassembly
• Inspect fasteners, shafts, and bushings; replace any that show wear or damage
• Tighten fasteners securely per the service manual; do not overtighten

PC-144 agitator that moves and tumbles clothes during wash cycles to help loosen soil and distribute water and detergent. Replacing a worn or damaged agitator restores proper wash action and improves cleaning performance. What it does:

• Uses fins/paddles to lift and move garments so water and detergent reach fabric fibers for better cleaning.
• Promotes even water circulation and load movement to reduce tangling and bunching.
• Common service reasons: cracked or broken fins, missing or worn agitator, noisy operation, excessive vibration, or clothes not coming out clean.
• Designed for top-load agitator-style wash systems that use the PC-144 agitator design.

• Disconnect power (unplug) and turn off water before starting any repairs.
• Typical replacement requires removing the existing agitator cap and any retaining hardware, then sliding the agitator off the drive post and installing the new unit; procedures vary by model—refer to your model's service manual or diagram.
• If a retaining bolt or special fastener is used on your model, have the correct socket or tool ready; follow manufacturer guidance for proper securing.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138