Kenmore Washer Dryer Combo 417.93702200 (41793702200, 417 93702200) Parts

Ordered a new handle from appliancepartspros.com and installed. Read more

• Doesn't shut off
• Timer will not advance

With a Phillips screw driver, on the back of the control panel there was about 6 or 7 screws to undo, to take the cover off and 2 screws holding the timer in place. Just undone those, took out old timer, made sure I took wires from old timer one at a time, and, put on new timer. Put everything back, although I had to find a couple of very small washers to make the timer fit tight, in the 2 holes it came out of. Luckily I had those or would of been a very loose timer. Very easy to do. Read more

Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day! Read more

The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more

I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more

• Will not stop filling with water

I removed two sheet metal screws to remove the panel above the washing machine lid. That exposed four more phillips drive sheet metal screws, after removing those the dashboard control panel is held by two smaller black screws slightly recessed in the lower corners. This allowed the panel to be pulled down from the top, revealing the back of the switch. At this point I took a picture of the wiring connections with my cell phone to make sure I put them on the new switch in the same... Read more

The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more

Found the model # on the washer door. Put the model # into appliancepartspros.com website, found within a minute or so. Ordered, received within a couple of days. We order from this company faithfully and have never had any delivery or order issues. Read more

Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more

Old, unused stack set. Washer was great, dryer was grinding. Started with the mounting bracket/bearing and the belt. The old ones were slightly beatup. Put it back together and the problem persisted. Found the real problem when I pulled apart the blower to get to the motor. The fan had broken fins that had jammed in the side of the blower housing, and the friction had melted through the outer wall of the fan. Got the blower housing from APP, got the fan from a competitors for $30 less. When it... Read more

Yes Read more

It took less than 5 minutes to fix it. It was very simple, the part fit perfect. I will keep this web site in my favorites for later use. Read more

The unit is 18 years old. This is the first thing I have don to it in all that time. The parts I ordered came quickly and installed with no problems Read more

Align plug and snap into place. Read more