Kenmore Dishwasher 587.14854200 (58714854200, 587 14854200) Parts

This replacement latch secures the door closed so the appliance can operate correctly. Restores a positive close and consistent door recognition to help prevent no-starts and intermittent operation. What it does / common symptoms:

• Engages the strike to hold the door/panel closed
• Ensures the door-closed signal is made so controls can run
• Worn or broken latch may cause the door not to stay shut
• Unit may not start, show a "door" message, or stop if the door is bumped

• 1 latch

• Disconnect power before servicing; turn off water supply if applicable
• Access the latch per model—typically behind the front panel or inner door liner
• Note and transfer any springs/clips from the original latch to the new one
• Verify smooth open/close and proper strike engagement before testing operation

This is a circulation pump motor for dishwashers. It controls the main pump of the appliance.The pump is directly responsible for removing extra water from the dishwasher after use. When a dishwasher's circulation pump motor goes bad, the main indicator is usually leaking from the appliance. There will be a noticeable amount of water emerging from the bottom of the machine whenever the cycle is engaged. Unplug the dishwasher from its main power source and water hookup. Remove the dishwasher from its space in the counter. Remove all necessary entry plates to access the interior of the dishwasher. There is a metal bracket holding the current motor in. Unscrew the two screws that secure the bracket and remove this component. Remember which way the motor is oriented before removing it. Unplug the power cable connecting the motor to the dishwasher. Put the two new sealing rings on the new pump motor. Repeat these instructions in reverse to install the new part.This Frigidaire dishwasher circulation pump motor is a genuine OEM replacement part sourced directly from Frigidaire. The pump motor is sold individually. This part is compatible with Frigidaire, Kenmore, Westinghouse, and Gibson appliances.

Includes one sprayarm.

The Dishrack Roller is an OEM part for Frigidaire dishwashers. This part ensures smooth and effortless movement of the dishrack in and out of the dishwasher. These rollers are attached to the sides of the dishrack, ensuring that it can glide easily without sticking or jamming, thus preventing damage to the dishes or the dishwasher itself.  

Causes of a bad Dishrack Roller can include wear and tear from regular use, damage from overloading the dishrack, or degradation of the roller material over time.  

Symptoms of a bad Dishrack Roller include:

• The dishrack sticking or struggling to move in and out
• A noisy operation when pulling the dishrack
• The dishrack tilting or becoming unaligned due to a missing or broken roller

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Set of 8 screws and washers.

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

Used on the upper rack track

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This short connector hose links internal dishwasher plumbing to move water securely between components. Replacing a worn or cracked hose helps prevent leaks and keeps cycles running reliably. What it does:

• Routes water between two internal connection points during the wash cycle
• Helps maintain a watertight seal when properly clamped
• Common symptoms: water leaking beneath the unit, dampness around hose joints, visible cracks/hardening, or a loose fit
• Aging hoses can stiffen and drip at barbed fittings

• 1 connector hose

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and pull the dishwasher forward as needed to access the hose
• Expect a small amount of residual water; have towels or a shallow pan ready
• Fully seat the hose on fittings, secure with appropriate clamps, then run a brief cycle and check for leaks

Black

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

This replacement screw secures appliance panels and internal components so they stay aligned and rattle-free. Replace missing or stripped hardware to restore a tight, reliable fit and prevent looseness that can lead to noise or damage.

• Fastens panels, brackets, or components to the chassis as designed
• Helps reduce vibration, rattling, and gaps from loose or missing hardware
• Restores proper alignment when an original screw is lost or threads are damaged
• Maintains safe, secure mounting of the original assembly

• Disconnect power (and shut off gas/water if applicable) before servicing
• Replace in the same location and orientation as the original hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Transfer any original washer or clip if present

The Hinge is an OEM part designed for Frigidaire dishwashers. It plays an essential role in supporting and controlling the movement of the dishwasher door, allowing it to open and close smoothly. This hinge ensures that the door remains securely in place during operation, which is vital for maintaining the appliance's efficiency and preventing leaks.

Causes of a bad hinge can include wear from repeated use, rust or corrosion due to moisture exposure, or physical damage from accidental force or impact. These issues can affect the hinge's ability to function properly, leading to operational problems.

Symptoms of a bad dishwasher hinge include:

• Difficulty in opening or closing the dishwasher door
• The door not staying open or closed securely
• Uneven or misaligned door movement

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement latch mounting screw secures the refrigerator door latch assembly so the door closes and seals properly. Installing a fresh mounting screw restores a solid latch connection and reduces door movement or rattling. What it does:

• Fastens the door latch assembly to the cabinet or door frame
• Keeps the latch aligned so the door closes and seals correctly
• Prevents loose or wobbly latch hardware and related rattling noises
• Helps address symptoms like a door that won't stay latched or minor door play

• Turn off power to the appliance or unplug before working near electrical components
• Use the correct screwdriver and thread the screw straight to avoid stripping
• Do not overtighten — snug is sufficient to hold the latch without deforming parts
• Test the door operation after installation