Kenmore Dishwasher 665.13032K110 (66513032K110, 665 13032K110) Parts

Quantity of ONE. Size: 8-18 x 5/8 inch. (#8 screw, 18 threads per inch, 5/8 inch long)

This wheel mount assembly fits the dishwasher's upper rack track and provides the roller that lets the rack glide in and out. Replacing a worn or broken mount restores smooth movement and keeps the rack aligned on the rails. What it does:

• Supports and guides the upper rack along the side rails
• Replaces cracked, missing, or seized rollers that make the rack hard to slide
• Helps prevent the rack from popping off the track or sitting unevenly
• Can reduce scraping or squeaking noises when moving the rack

• One upper rack wheel mount assembly

• Disconnect power to the dishwasher before servicing
• Open the door and remove the upper rack by releasing the rail stops
• Depress the locking tab to remove the old wheel mount from the rail; align and snap the new assembly into place
• Reinstall the rack and rail stops; check for smooth rack travel

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This vent housing assembly mounts in the dishwasher door to guide humid air out of the tub. A secure, sealed housing helps prevent steam leaks and moisture damage while supporting proper airflow during the dry portion of the cycle.

• Provides a sealed mounting point for the door vent
• Channels moist air out during drying to protect the door and control panel
• Helps prevent steam or moisture from escaping at the top of the door
• Common symptoms: steam or dampness at the door top, water streaks on the front panel, or visible cracks/warping in the housing

• Disconnect power at the breaker and turn off water supply before servicing
• Remove inner door panel fasteners to access the vent area
• Note orientation; transfer any gasket or retainers from the original housing if required and seat the new housing flush
• Reassemble and run a short cycle to check for leaks and proper airflow

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This dispenser water tube routes water from the inlet to the refrigerator's in-door dispenser manifold, helping ensure a steady, leak-free flow to the dispenser.

• Directs water from the supply line to the dispenser manifold
• A damaged or cracked tube can cause leaks, low/erratic dispenser flow, or air in the water line
• Replacing a leaking tube can help restore normal dispenser operation and prevent water damage

• Unplug refrigerator and shut off water supply before service
• Have a towel/container ready to catch residual water
• Note tube routing and connections; push-to-connect fittings may require firm seating for a watertight seal
• After installation, turn water on and check all joints for leaks

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

This cap is a small protective cover used on select appliances to close off an opening or fastener. Replacing a damaged or missing cap helps keep out debris and moisture while restoring a clean, finished appearance.

• Covers an exposed opening or fastener to protect internal components
• Helps keep out dust, moisture, and spills
• Restores a clean, finished look and prevents snags
• Replace if the original cap is cracked, missing, discolored, or won't stay seated

• Disconnect power and, if applicable, shut off water or gas before service
• Remove the old cap by pulling straight off or unthreading, as designed
• Align the new cap and press or thread into place without forcing
• Verify a secure fit before restoring power and connections

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.

• Secures the heating element to its mounting point to keep it stable
• Maintains proper spacing from nearby components and surfaces
• Helps reduce vibration, rubbing, or rattling noises
• Replace if the original support is cracked, warped, missing, or the element appears misaligned

• Disconnect power to the appliance before servicing; allow hot components to cool
• Access the heater per your model's service information; note the original orientation and routing
• Seat the support fully and handle element leads carefully to avoid damage

Bushing, Door spring

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

This replacement handle restores a secure, comfortable grip so you can open and close your appliance smoothly. It replaces a cracked, broken, or loose handle to bring back reliable operation and a clean, factory look.

• Provides sturdy leverage to open and close the unit's door or drawer
• Attaches to existing mounting posts or screws on compatible models
• Helps resolve issues like a loose, wobbly, cracked, or missing handle
• Restores appearance when the original handle is scuffed or damaged

• Disconnect power before servicing; also shut off water
• Protect the surface with tape or a cloth to avoid scratches during removal/installation
• Align the handle carefully; start fasteners by hand to prevent cross-threading
• Tighten evenly and only until snug to avoid damage to threads or trim

Size: 1/4 inch hex head, 10-12 x 1/2 inch.