Kenmore Dishwasher 665.13594K600 (66513594K600, 665 13594K600) Parts

These dishwasher cleaner tablets help dissolve and remove limescale, mineral deposits, and odor-causing residues from the tub and spray system. Use monthly or as needed to help maintain cleaning performance and a fresh-smelling interior.

• Breaks down hard-water scale and detergent film that can accumulate inside the dishwasher
• Helps reduce lingering odors caused by trapped residues
• Supports proper spray performance by cleaning internal surfaces and passages
• Helpful when you notice white film, cloudy glassware, or persistent smells

• Run with the dishwasher empty; follow the package directions for tablet placement and cycle selection
• Do not add other cleaners or detergent during the cycle
• Keep out of reach of children; avoid contact with eyes; wash hands after handling
• For heavy buildup, repeat use per label instructions

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

The Lower Dishwasher Rack Assembly is an OEM part for Whirlpool dishwashers. This part holds and organizes dishes, pots, and pans in the lower section of the dishwasher, ensuring they are properly positioned for effective cleaning.

Causes of a bad lower rack can include wear and tear from regular use, exposure to harsh detergents or high temperatures, and physical damage from heavy or improperly loaded items. 

Symptoms of a bad lower dishwasher rack assembly include:

• Rust or corrosion on the rack
• Broken or missing tines
• Difficulty sliding the rack in and out
• Poor arrangement of dishes, leading to ineffective cleaning

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This seal kit is for the main tub. It goes around the pump housing.

Notes: Only one screw hole is used now.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

Screw for wash impeller.

This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:

• Drives water through the drain pump so the washer can empty properly
• Worn or broken impellers can cause slow or no draining and standing water
• May produce unusual pump noise or vibration when damaged
• Helps prevent motor overload by maintaining proper water flow

• One drain impeller

• Disconnect power before accessing the pump assembly to avoid electric shock
• Inspect the pump housing and fasteners; replace any damaged clips or seals as needed
• Reassemble pump and test a short drain cycle before completing the repair