Kenmore Dishwasher 665.13949K012 (66513949K012, 665 13949K012) Parts

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

This sump and motor assembly replaces the lower tub sump with the circulation pump pre-installed. It restores proper water recirculation to the spray arms and a tight seal at the tub floor to help reduce leaks and noise.

• Circulates wash water through the spray arms for consistent cleaning performance
• Channels and filters water beneath the tub via the integrated sump
• Maintains a watertight seal at the tub base
• Common symptoms of failure: weak or no spray action, poor cleaning results, loud humming/grinding during wash, or water leaking from the center bottom area

• Disconnect power and turn off the water supply before servicing; allow internal components to cool
• Remove the lower rack, spray arm, and filters to access the sump; disconnect hoses and wiring, then release the locking tabs to remove the assembly
• Ensure all seals/O-rings are properly seated; fully engage hose and electrical connections to prevent leaks
• After installation, run a brief test cycle and inspect carefully for leaks before reassembling panels

This is a Whirlpool control board intended for use with dishwashers.The control board is a critical component of the dishwasher as it controls the cycles and functions, including the draining and drying cycles. Control boards are subject to wear and tear that can render them ineffective and require them to be replaced prior to the standard lifecycle of the appliance. Unplug the dishwasher from both the power and water sources before attempting to replace the control board to prevent serious electrocution injuries. Work gloves should also be worn.This OEM control board has been sourced from the manufacturer and is compatible with dishwashers from Whirlpool, Maytag, Kitchenaid, Magic Chef, Admiral, Norge, and other brands. This part has been made from high-quality, durable, non-corrosive materials and is only sold individually.

Color: light grey. It measures about 2-1/2 inches high by 2 inches deep.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

This spray arm distributes wash water inside the dishwasher, rotating to deliver even spray coverage across the racks. Replace a cracked or clogged arm to restore consistent cleaning performance and reliable water distribution.

• Directs pressurized water through jet openings while spinning to wash dishes evenly
• Helps address symptoms such as poor cleaning results or uneven spray coverage
• Replace if the arm is cracked, warped, mineral-fouled, or no longer spins freely
• Damage or improper seating can cause the arm to strike dishes/tub and make noise

• Disconnect power to the dishwasher before servicing
• Remove rack(s) if needed; release the arm by unscrewing the retainer or pressing the locking tab (method varies by model)
• Clean debris from the mounting hub and seal surfaces before installing the new arm
• Seat fully, ensure the arm spins freely with proper clearance, then run a test cycle

Includes two screws, two clamps, and undercounter mounting brackets.

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This factory screw secures panels, brackets, or components within your appliance. Using the correct OEM fastener helps ensure a snug fit and prevents loosening, rattling, or misalignment over time.

• Fastens metal or plastic components to maintain proper alignment
• Helps prevent vibration, noise, and loosened parts
• Common wear item that can strip, rust, or go missing
• Replaces damaged or missing hardware to restore secure mounting

• Disconnect power and shut off water or gas before service
• Note original screw location and orientation for proper reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• If threads are damaged, inspect the mating hole or clip before reuse

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

Insulation pad that fits behind appliance panels to restore thermal protection and reduce noise. Replacing a damaged or missing pad helps protect nearby wiring and components from heat and can reduce vibration-related rattling. What it does:

• Provides thermal insulation to help limit heat transfer to adjacent panels and components.
• Dampens vibration and reduces rattling or buzzing caused by loose or worn insulation.
• Protects wires, connectors and plastic parts from excess heat when installed correctly.
• Common symptom: missing, torn, or deteriorated pad with increased exterior heat or noise.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove access panels as needed; position the pad flat against the cabinet surface or mounting area.
• Use original clips/adhesive or manufacturer-recommended fasteners to secure the pad; avoid covering vents or controls.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This machine screw secures panels, brackets, and other components inside your appliance. Replacing a missing or damaged fastener restores a solid fit, reduces vibration and rattling, and helps keep assemblies properly aligned for reliable performance.

• 10-32 machine-thread fastener for mounting and securing internal parts and panels
• Helps maintain alignment and structural integrity of assembled components
• Replaces missing, stripped, or damaged hardware
• Reduces rattling, vibration, or loosening from worn fasteners

• Disconnect power; shut off gas or water supplies before servicing
• Match thread and length to the original fastener used in that location
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse original washers or clips if present and in good condition