Kenmore Dishwasher 665.16332400 (66516332400, 665 16332400) Parts

These dishwasher cleaner tablets help dissolve and remove limescale, mineral deposits, and odor-causing residues from the tub and spray system. Use monthly or as needed to help maintain cleaning performance and a fresh-smelling interior.

• Breaks down hard-water scale and detergent film that can accumulate inside the dishwasher
• Helps reduce lingering odors caused by trapped residues
• Supports proper spray performance by cleaning internal surfaces and passages
• Helpful when you notice white film, cloudy glassware, or persistent smells

• Run with the dishwasher empty; follow the package directions for tablet placement and cycle selection
• Do not add other cleaners or detergent during the cycle
• Keep out of reach of children; avoid contact with eyes; wash hands after handling
• For heavy buildup, repeat use per label instructions

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

This seal kit is for the main tub. It goes around the pump housing.

Notes: Only one screw hole is used now.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

Screw for wash impeller.

This heater support secures the dryer heater assembly so it stays aligned and stable during operation, helping maintain proper airflow and heating performance. It's a direct-fit replacement designed to restore correct heater positioning. What it does:

• Holds the heater assembly in place to prevent shifting or contact with other components
• Helps maintain proper airflow path for efficient drying and consistent heat
• Reduces rattling, rubbing, or intermittent heating caused by a loose heater
• Works with the heater housing and mounting points to keep electrical and thermal parts separated

• Refer to the dryer's service manual or parts diagram for correct placement and orientation
• Disconnect power before starting work to avoid electrical shock
• Inspect surrounding clips, screws, and the heater assembly; replace any damaged fasteners

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This O-ring is a small rubber replacement seal that helps stop water leaks where two components meet. It restores a tight seal to reduce drips and prevent water damage from worn or cracked seals. What it does:

• Provides a compression seal between mating parts to prevent leaks
• Commonly replaced when visible cracking, flattening, or hardening occurs
• Helps eliminate steady drips or pooling of water near the seal area
• Restores proper sealing after disassembly for service or part replacement

• Disconnect power and shut off the water supply before servicing
• Remove surrounding components carefully to avoid damaging the seal seat
• Inspect the mating surfaces for debris or damage; clean before installing new O-ring
• Lubricate with a compatible, appliance-safe lubricant; do not use petroleum-based products unless specified