Kenmore Dishwasher 665.16579201 (66516579201, 665 16579201) Parts

The Gasket is an OEM part for Whirlpool dishwashers. This gasket seals the gap between the dishwasher door and the main tub, preventing water from leaking out during the wash cycle. It ensures a watertight seal that helps maintain the efficiency and performance of the dishwasher.

 Over time, the gasket can deteriorate due to regular use, exposure to heat, and contact with detergents. A faulty gasket can lead to water leaks, which may cause damage to surrounding cabinetry and flooring.

Symptoms of a bad dishwasher gasket include:

• Water leaking from the bottom or sides of the dishwasher door
• Visible cracks or tears in the gasket
• The dishwasher door not closing properly
• Increased noise levels during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement lever operates the overflow/level switch assembly to help the washer detect and respond to water level changes. It restores the mechanical action that tells the control when the tub is full. What it does:

• Moves the overflow/level switch mechanism so the machine can sense water level correctly
• Helps address overfilling, continuous filling, or erratic fill behavior caused by a worn or broken lever
• Restores reliable engagement between the float/actuator and the switch
• Works as the mechanical linkage for the overflow/level sensing assembly

• Disconnect power and turn off the water supply before beginning service.
• Access typically requires removing the cabinet or control console; keep fasteners organized.
• Install the lever so it aligns with the switch actuator and float linkage; verify smooth movement after assembly.

This pump sump screen filters lint, debris and small objects from wash water before it reaches the drain pump, helping prevent clogs and pump damage. Replace a cracked or clogged screen to restore proper draining. What it does:

• Captures lint, coins, hair and small debris before the drain pump
• Helps prevent pump blockages that cause poor draining or standing water
• Reduces wear on the drain pump by stopping larger debris
• Improves overall drain performance when the existing screen is damaged or clogged

• Disconnect power and water before accessing the pump area
• Remove the washer access panel or cabinet per your model's service instructions to reach the sump
• Inspect and clean surrounding areas and the pump inlet when replacing the screen

A small replacement retainer that secures the FlexRow assembly so the component stays aligned and stable during use. Replacing a worn or broken retainer restores proper positioning and reduces movement. What it does:

• Holds the FlexRow assembly in place to prevent shifting or sagging
• Helps maintain correct alignment for even operation
• Stops clicking, rubbing, or intermittent contact caused by a loose assembly
• Prevents additional wear on adjacent clips or mounts

• Disconnect power to the appliance before beginning any repair
• Removal usually requires releasing adjacent clips or fasteners; basic hand tools may be needed
• Inspect surrounding parts and replace any damaged clips or mounts for a secure fit

This dual positioner assembly helps align and hold the control shaft/knob mechanism so selections register correctly and controls operate smoothly. It replaces a worn or broken positioner to restore reliable selector alignment. What it does:

• Secures and centers the control shaft/knob so detents register properly
• Prevents loose or wandering knobs and helps ensure accurate cycle selection
• Commonly replaced when knobs feel sloppy, skip positions, or controls don't stay set
• Works with the control panel mounting to stabilize selector movement

• Disconnect power to the appliance before starting any work
• Remove the control panel or console to access the positioner per your model's service instructions
• Handle plastic tabs and mounting points carefully to avoid breakage during removal/installation
• Test control function after reassembly to confirm correct alignment and operation

This inlet water bezel is the trim piece that fits around the washer's water inlet to provide a finished opening and support the inlet connection. It restores appearance and helps position the inlet area for a proper hose fit. What it does:

• Covers and finishes the water inlet opening on the cabinet for a clean appearance
• Helps hold and align the inlet connection and hose to reduce stress on the valve
• Prevents direct contact between the inlet hose/valve and the cabinet edge
• Commonly replaced when the inlet trim is cracked, broken, or worn

• Disconnect power and shut off the water supply before starting
• Remove the appropriate access panel or control console to reach the inlet area
• Handle the bezel carefully to avoid scratching painted surfaces during install
• Re-check inlet hose routing and tighten connections; test for leaks after restoring power/water

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

The Whirlpool push on retainer nut is an OEM replacement part responsible for securing the heating element in the dishwasher. It is located in the base of the dishwasher's tub to hold the heating element firmly in place. The push-on retainer nut keeps the heating element securely connected to the dishwasher's electrical system while allowing for easy removal and replacement when necessary.

Over time, push on retainer nuts can become loose, worn out, or damaged due to regular use, vibrations, or accidental mishandling. If a retainer nut fails, it can lead to parts becoming unstable or disconnected.

Symptoms of a bad push on retainer nut include:

• Loose or unstable dishwasher components
• Parts falling off or becoming misaligned
• Unusual noises during the wash cycle
• Difficulty in securing components within the dishwasher

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models

The Dishwasher Drain Pump is an OEM part for Whirlpool dishwashers. It is responsible for removing water from the dishwasher at the end of each cycle, ensuring that dishes are properly cleaned and dried.

Causes of a bad drain pump can include wear and tear from regular use, blockages from debris, or electrical malfunctions.  

Symptoms of a bad drain pump include:

• Water not draining from the dishwasher
• Unusual noises during the drain cycle
• Error codes related to drainage issues
• Water pooling at the bottom of the dishwasher

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.