Kenmore Dishwasher 665.17824000 (66517824000, 665 17824000) Parts

This fill and drain hose assembly connects a portable dishwasher to a sink faucet, delivering incoming water and routing wastewater back to the sink. Replacing a worn assembly restores a secure connection and helps prevent leaks during operation.

• Integrates inlet and drain hoses with a faucet coupler for quick, tool-free hookup
• Supplies water to the dishwasher and returns drain water to the sink
• Can address no fill or no drain symptoms caused by a damaged or obstructed hose/coupler

• Safety first: Unplug the dishwasher and turn off water before servicing
• Expect residual water; place towels/pan and relieve line pressure
• Ensure a compatible faucet adapter is installed; attach the coupler fully and verify a good seal
• Route hoses without kinks, secure the drain end to the sink, and check for leaks on first run

There is a split at the 3 O'clock position. Color: white. It measures about 3 inches wide by 4 inches high.

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This felt door vent seal fits around the dishwasher's door vent to help contain steam and moisture within the inner door. Replacing a worn seal helps prevent minor leaks and condensation around the vent area during cycles.

• Creates a gasket between the vent assembly and inner door panel to keep steam directed through the intended vent path
• Reduces moisture escape that can cause drips or water spots on the outer door or nearby countertop
• Helps limit condensation or musty odors from trapped moisture inside the door panel
• Indicators of failure include visible wear or separation of the felt and moisture around the vent during operation

• Disconnect power and turn off water supply before servicing the dishwasher
• Remove the inner door panel to access the vent assembly
• Note the seal's orientation; clean mating surfaces; seat the new felt evenly around the vent with no gaps
• Reassemble and run a short test cycle to check for leaks at the vent area

Detergent cup dispenser actuator assembly.

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Includes washers.

Almond. Size: 13 oz. can. Acrylic appliance paint.

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

This small check ball sits inside a check valve to allow one-way water flow. Replacing a worn or missing ball helps prevent backflow and supports reliable draining performance between cycles.

• Maintains one-way flow through the valve to stop water from returning after the pump stops
• Helps ensure complete, consistent draining
• A damaged, swollen, or missing ball can let water back up into the tub/sump
• Contribute to slow or intermittent draining and unusual gurgling/flow noises

• Disconnect power and shut off water before servicing
• Access the check valve assembly per your model's service information (commonly at the sump, pump outlet, or drain connection)
• Clean the valve seat/passage; remove debris that could prevent sealing
• Place the ball in the valve seat as shown in your model's parts diagram; reassemble and test for leaks and proper flow

This tub wheel mount secures the rack support roller to the dishwasher tub wall so racks roll smoothly. Replace a cracked or loose mount to restore smooth rack movement and prevent binding or sagging during loading and unloading.

• Secures the tub roller/wheel to the dishwasher's inner tub wall
• Provides a stable point so the rack glides smoothly on its track
• Helps keep the rack level and properly aligned
• Common symptoms: rack hard to slide, tilts or drops, scraping/grinding when moving the rack

• Disconnect power and water supply before servicing
• Pull the rack forward to access the mount on the tub sidewall
• Remove the retaining fastener or release locking tabs, then install the new mount in the same orientation
• Ensure the wheel engages the track and test rack travel for smooth operation

Color: Almond

This is the upper spray arm that distributes wash water to the top rack. Replacing a cracked, warped, or clogged arm restores even spray coverage and helps the arm spin freely so glasses and bowls come out consistently clean.

• Directs high-pressure jets to the upper rack and rotates under water pressure for full coverage
• Maintains even water distribution to improve cleaning performance
• Common symptoms of a failed arm: top-rack items not getting clean, arm not spinning, uneven spray, cracks or clogged nozzles

• Disconnect power and water supply before servicing the dishwasher
• Remove or lower the upper rack if needed; release the retaining nut/clip and pull the old arm straight off
• Seat the new arm fully on the hub/manifold and secure the retainer; verify it spins freely
• Run a short test cycle to ensure proper spray and operation

Comes with seal.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.

• Screens the door vent to keep debris out of the vent duct and fan path
• Maintains airflow for venting steam during the dry cycle
• A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
• Replace if warped, broken, or lost during service

• Disconnect power to the dishwasher at the breaker before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
• Run a short cycle and check the vent area for proper airflow and moisture