Fred February 17, 2014 for Model Number FDB4050LH1 Hi, I replaced the pump motor yesterday and when everything was put back and turned on the new motor came on immediately. I called frigidaire and the tech said it sounds like a control board issue. Please Help
1 Answer Hello Fred, Try to let it clear out first. If it never stops, replace the board on the unit. Read More...
Jim C February 06, 2014 for Model Number Frigidaire Dishwasher PLD4375RFCO My dishwasher does not have any display light in the panel. It is somewhat tricky because when you open the door all the way down,it would lit PF.So what I will do is push the cancel button and press the operation button like Speed Clean or any button and then press the Start button and it will function like the hot water is coming out from the left side. But I would stop it because the water rises and the door is open. So I am thinking that my control panel could be ok and that I guess there could be some cut in the harness,that when I move the door down there is a certain portion that it supplies power and the display comes out . What could be the fault of my dishwasher?
1 Answer Hello Jim. You need to check the terminal block and the harness for a bad wiring issue. Read More...
Michael February 05, 2014 for Model Number FDB4315LFC2 Display and control panel stopped working, got replacement main control board per recommendation, after replacement the display changed codes to "91" and the China wash light remains on but the dishwasher still does not work and none of the buttons work. Changing back to the original board, the display now only displays the "91" and china setting, the original error code is gone. A previous search for the issue showed the touchpad and control panel to potentially be the problem.
1 Answer Hello Michael, This sounds like you have a stuck key on the console assembly 154639208. Read More...
Melody January 21, 2014 for Model Number fghd2433kf1 I just ordered a new control board for my dishwasher. Does it come with a diagram on how to install the new one? If not where can I find out how to remove the old and install the new.
1 Answer Melody, The control board does not come with a diagram on how to install the new one. In order to replace the control board you would need to turn the power off to the unit, open the dishwasher door and remove the screws around the perimeter of the door. This will allow access to the control panel. You will remove the cover over the control board and transfer one wire at a time to the new control board and reassemble. Read More...
Don S January 01, 2014 for Model Number PLD4375RFC0 My dishwasher is still working properly, after the cycle ends there is a very small amount of water in the bottom (can only be seen when removing the screen and such). The issue started a few weeks ago when I noticed a sound coming from the washer after the cycle was over, it was a gurgling noise. It would make this noise for a few minutes then stop. Now it is constant. I tripped the door switch and found out that the pump is still pushing that small amount of water back thru the center post. Luckily I have an on/off switch installed so I can stop it after the cycle. But I have noticed that now during the full cycle it sounds like it is constantly pumping water, even during the heating/drying phase. It seems that the only culprit can be the control board, but wanted to verify this before I laid out the $$ for it. Thanks for any advice you can give.
1 Answer Don, Based on the description, If the pump is continuously running and causing a gurgling type of noise during the cycle and after it would be caused by a faulty control board but you will also want to check to make sure that the wiring to the drain motor is in good condition. Make sure that there are no breaks or damage to the wires. Read More...
Michelle December 11, 2013 for Model Number Frigidaire Dishwasher GLD4355RFS I have someone telling me that MPN 154543602 is the same part as MPN 154757002. I was hoping you would be able to confirm or deny? Appreciate the help!
1 Answer Michelle, 154543602 is no longer available and has been replaced by the manufacturer with part number 5304514670. Thanks! Read More...
Tiffany December 09, 2013 for Model Number fghd2433kf1 After the cycle, the dishwasher still runs? (no lights are on)
1 Answer Hello Tiffany. If the motor still runs, and the unit is off, replace the control board in the unit. Read More...
Brooke October 16, 2013 for Model Number FDB4315LFCO RE: Frigidaire Dishwasher Aqua Surge with Speed Clean I have 12 buttons on my control panel but only 4 on the left side work/light up. These include: Ultimate Scrub, Speed Clean, Normal Wash, China Crystal. (The ultimate scrub activates the hi temp wash and the sanitize buttons which also seem to work because they light up when ultimate scrub is selected.) What parts might I need to fix this?
1 Answer Hello Brooke. It sounds like the control panel 154639208 is bad and will need to be replaced on the unit. Read More...
Ray October 15, 2013 for Model Number FGHD2433KB1 When power is applied display lights up for a few seconds and then goes dark as if it lost power. Power is still applied. I suspect control board but not sure.
1 Answer Hello Ray. Look for a wiring issue. If none is found, you will need to replace the control board in the unit. Read More...
Ray September 27, 2013 for Model Number PLD4375RFCO Do you carry a control board for this dishwasher?