Glenn August 09, 2014 for Model Number FGHD2433KF1 Home took a lightening strike and when we came home the dishwasher was running with no water. The only way you can stop it is to open the door. there are no lights on but unit runs when the door is closed. Will a control board fix this?
1 Answer Hello Glenn. Yes, it sounds like you need to order and replace the control board on the unit. Read More...
Barry Marsh August 03, 2014 for Model Number FGHD2433KF1 When washer is set for quick wash, the display starts out at 50 minutes and starts to count down for a few minutes while running then suddenly switches to 99 minutes and runs a normal wash cycle. This has been going on for some time so I don't think its related to the problem below. Also, I have just replaced the water fill valve as the water level was low and its still low. The float is free, the water comes in but the water level never gets high enough to actuate the float.
1 Answer Barry, Based on the information it sounds like the control board would be the issue with the unit going from 50 minutes to 99 minutes and be in normal wash. As far as the water level goes you will want to check to make sure that the water valve is not clogged and if not then it could be the control causing this issue also. Read More...
Janet July 22, 2014 for Model Number FGHD2433KF1 The power starts to work and looks like it is going to run. As soon as it gets started, it goes off and flashes ER UO over and over. It will not work.
1 Answer Janet, The ER UO error indicates a vent open error. While in wash cycle, Main Control Board does not receive signal from vent assembly that vent plunger is closed. Plunger status is sensed with optical sensor in vent assembly. Check wiring between vent assembly and Main Control Board. If wiring correct, replace vent assembly. If error still exist, replace Main Control Board. Read More...
Sara S. July 20, 2014 for Model Number FGHD2465NF1A I have ER flashing sign with the rinse light on all the time. Nothing I can do to change the order. Thank you
1 Answer Hello Sara, An ER code usually means the control panel 807545704 has experienced a switch failure or a lost connection. Read More...
Steven May 17, 2014 for Model Number Frigidaire fghd2465nf dishwasher Recently our power went out and when it came back on, our dishwasher is displaying the number 8 only. We've tried to turn off the power for 30 minutes in hope of resetting, but have had no luck. All buttons appear to not be functioning - is there something we can replace to make this guy work again? Thanks!
1 Answer Steven, Yes, you want to start by replacing the control panel assembly 807545704. It is the more likely issue, based on your description. The number 8, and the other buttons not working indicates several keypad circuits have failed and are inputting too many circuits and causing the control board to "lock up" and not operate. Read More...
John May 15, 2014 for Model Number Pld4375rfc3 The dishwasher went dead no lights on the panel and would not start. I checked the breaker and it was good. At one point I got a power failure reading on the panel and it reset. It ran once and went dead again. The power to the unit is good I checked with a meter and I have power up to the latch. I could not tell if I had power at the board.
1 Answer Hello John. If all the wiring connections are good, you will need to order and replace the control board on the unit. Read More...
Alex D. April 19, 2014 for Model Number PLD4375RFC0 All my left buttons work and light up but when I try to start it, nothing works , I don't know what I need.
1 Answer Alex, You want to start by replacing the control panel / keypad assembly 154639207. It's the more likely issue based on your post description. We don't have a key pad test matrix to circuit test the pads, so you'll need to replace the assembly. Read More...
Amy R March 30, 2014 for Model Number FGHD2433KF1 My frigidaire gallery dishwasher model#FGHD2433KF1 has sporadic problems with the computer panel. First the NORMAL WASH cycle button wouldn't work and now the START/STOP button works off&on. I can use a different cycle but then hit START and it won't start. I keep mashing it and mashing it and finally it will start. Sometimes I have to walk away and come back several times and mash it and eventually it will start. Sometimes it does fine for days then suddenly the problem starts again. What is causing this? A short? Can a short be fixed or do I need to replace the control board? Or is it the console?
1 Answer Amy, You will want to access the control board by taking the screws from the inner door panel. With the panel lifted up you will want to check the connection of the ribbon harness from the control panel to the control board. You will want to make sure that there is no corrosion and that the harness is fully seated. If it checks ok then you would want to replace the console as it sounds like the keypad is the issue. Read More...
Jason March 14, 2014 for Model Number FGHD2465NF Dishwasher lower orbit spray arm broke off. We still used the dishwasher for a few days after that, but an error code appeared. I ordered an new lower orbital spray arm and installed it. The code still appears. The dishwasher will oprate on the rinse option only. It rinses and drains fine but will not heat. The error code is washing, drying, ER clean S. Is this the keypad ? thx.
1 Answer Jason, Yes, the error code that you have represents a Membrane switch failure. Main Control Board has detected a stuck key or a key pressed for more than one minute. Check connection from keypad to Main Control Board. If correct, replace keypad. If error still exist, replace Main Control Board. (Note: washing, drying, and clean s may appear in display when error code is present) Read More...
David February 24, 2014 for Model Number fdb4315lfc3 Dishwasher stops somewhere mid cycle, and shows PF on display screen. Sometimes can restart and finish wash. Sometimes problem re-occurs
1 Answer Hello David. Based on the information you provided, you need to order and replace the control board on the unit. Read More...