Jim S September 05, 2013 for Model Number FGHD2465NF I attempted to rebot the dishwasher however half-way through the cycle it displays ER Clean S. What is the malfunction and how do I fix it?
1 Answer Jim, The Er Clean S error is a faulty keypad 807545704. To replace you will need to remove the inner door, the control board, the latch assembly and the vent. Once removed there will be a couple of screws holding it to the from panel. Remove the screws and swap the console. Reinstall all parts. Read More...
Michael C August 26, 2013 for Model Number FGHD2433KB1 When trying to use the dishwasher after pressing normal wash the indicator light illuminates and the 99+ illuminates then after pressing start the panel clears after 15 seconds and the dishwasher will not start. This machine is only 1 year old and has only been used less than 20 times. Could the control board be malfunctioning already? Tried opening the breaker to the dedicated circuit for 1 minute this did not help but I got a UL code for a few minutes.
1 Answer Michael, The UL code is for the UL test mode and is only displayed in relay test mode when UL test is activated. Based on the information provided it sounds like the control board may be at faulty control board causing the issue. Read More...
Rodolfo August 12, 2013 for Model Number PLD4375RFCB Hi. Do you have the control board for this machine? Thanks
Russ G August 05, 2013 for Model Number FDBB4365FC3 dishwasher wouldn't do anything. lit up with 91 showing on screen. tried cancel and removing power. wouldn't do anything. a day later it cleared and when I started it it ran for awhile but now have Er on screen. Can clear but will just do it again. had control replaced a couple years ago under warrenty but not working again.
1 Answer Russ, The "ER" error code indicates a key pad failure 154639207 . " "Er" > Membrane Switch failure > When the control verifies that any of the pads on the membrane switch has been closed for one minute the failure will appear in the display". The circuit for the start/cancel key has most likely failed, so the dishwasher won't start. Read More...
Bob July 30, 2013 for Model Number frigidaire series 2000 dishwasher with status window When I start the dishwasher (normal cycle), everything is fine. The status window reflects the number of minutes remaining. About 20-25 minutes into the wash, the status window shows "CL", no more minutes remaining and if you don't cancel the wash it will continue to wash and wash and wash.
1 Answer Hello Bob. Based on the information you provided, it sounds like the control board 5304514670 is bad and will need to be replaced on the unit. Read More...
Big B July 14, 2013 for Model Number FGHD2433KF1 Recent lightning strike with surge to dishwasher. Dishwasher came on automatically when lighting surge happened. Now dishwasher will not go through full cycle. Once applying power to dishwasher it is on automatically without pressing start button.
1 Answer Hello Big B. It sounds like the control board is bad and will need to be replaced in the unit. Read More...
Regina June 02, 2013 for Model Number FGHD2465NF The dishwasher would start running and then cut off and the LED would show PF. After doing this a couple of times the entire circuit that the dishwasher was on would not work. I talked to an electrician about this and after unplugging the dishwasher the rest of the circuit worked. The electrician tested the power going to the dishwasher and the resistance on the dishwasher and the power going to the dishwasher was fine but the resistance was extremely high. Does this mean that the board control is bad?
1 Answer Hello Regina, The first thing that raises a flag is the fact that the manufacturer requires that the unit be on a dedicated circuit. The board can have an issue, but until the unit is run on a dedicated circuit, there isn't much of a way of knowing if the unit has a problem or if the problem is installation related. Read More...
Marcus June 01, 2013 for Model Number FDB4315LFC0 My curculating pump keeps running when it shouldnt. I tested the blue wire P3-4, and it has 115 volts when it should be on and between 11 and 70 volts when it should be off. This allows it to run at a slower speed. This can even happen when it is off.
1 Answer Marcus, You will want to check your wiring to make sure that there is not a short to ground which would cause power to get to the motor. If this checks ok then the control board would be the issue. Read More...
Riley May 30, 2013 for Model Number GPDB998JCO Lights display only on half the dishwasher and they only stay lit for 10 seconds. Nothing happens when I push the start button. Dishwasher was working fine until we pushed the time delay button and nothing happens other than a few lights glowing for a few seconds. What's wrong? w
1 Answer Hello Riley. Based on the information you provided, it sounds like the control panel keypad 154369701 is bad and will need to be replaced on the unit. Read More...
Jeff May 08, 2013 for Model Number fdb4050lhb1 Unit about 4 yrs old. Shut dishwasher door, hit start button, and unit does not start cycle. Control panel lights up for approx. 2 seconds then shuts down leaving control panel black. I have repeated process and continues same symptom .
1 Answer Hello Jeff. It sounds like either the control board or the door switches are bad on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...