Yvonne April 03, 2023 for Model Number FGCD2456QFOA I need to replace my door control panel. I can't read the function panel plus the buttons are broken. Where can I find this part or is it better to buy a new dishwasher? It is 8 years old. Thank you
1 Answer Yvonne, the control panel A00035004 would be used with the model number provided. Read More...
Tony March 03, 2023 for Model Number FGHD2465NF1A When I start a normal wash it goes to washing 99t and the time doesn’t change.
Wanda February 06, 2023 for Model Number fgid2466qf4a I press start & cd appears as usual. then it clicks off & looks like u6 appears. do I need a new control panel ?
1 Answer Wanda, unfortunately, the error code u6 would be an invalid error. This would indicate a failure within the main control board 5304514670. Read More...
Serge October 08, 2022 for Model Number FGHD2465NF1A I have two identical FGHD2465NF1A units. Unit A stops mid-cycle and flashes Error message on the LED display. Unit B works well. I switched both main control board and console between the units. Unit B functions well as before while Unit A still stops mid-cycle and flashes Error message. What could be wrong with Unit A?
1 Answer Serge, If you could provide what the error code is that the unit is flashing it would help with being able to determine what is going on with the unit. Read More...
Serge September 30, 2022 for Model Number FGHD2465NF1A I replaced Main Control Board on FGHD2465NF1A unit with part #5304514670 which is a replacement for #5304504782. The display and controls now behave completely differently from before. For example when choosing Normal cycle instead of previous "99+" on the LED display it now shows 33 and flashing "S" which I assume is for sanitizing. There is no combination that gets rid of "S" choice. Is it a bad part or something has changed in the way this Control Board operates?
1 Answer Serge, the power supply would need to be turned off and the wire connections checked to ensure there is not a loose connection. If the failure continues, the control board 5304514670 would be an issue depending on what the original failure was. Read More...
Cece January 21, 2022 for Model Number Kenmore Elite Dishwasher Model. 665.12773K314 My Kenmore dishwasher stays on continuously when programmed in the Smart cycle. Other cycles seem to work fine. Is this a timer or a control board issue. Dishwasher was purchased in 2015.
1 Answer Cece, With the unit working on all cycles except 1 properly then this will be a faulty control board. Read More...
Dan October 13, 2021 for Model Number FGID2474QF4B Apparently the control board for this dishwasher is underneath the unit. So it has to pull from under the cabinet to access yes?
1 Answer Dan, It would be recommended to pull the unit out to access the dishwasher bottom. Read More...
Dan October 13, 2021 for Model Number FGID2474QF4B Unit needs a new control board . Went to replace it but it’s not in the door. Is it located under the unit? Or where?
Jstone October 05, 2021 for Model Number PLD4375RFC1 Three of the cycle buttons on my control panel do not work. I've been told the control panel needs replacing at $237. I've not taken it apart to see how the buttons work or the connections. Could it just be the button connections that are bad and not the panel?
1 Answer Jstone, as there is only partial failure on the user interface, the failure would be in the console assembly 154639207. Unfortunately, this part has been discontinued by the manufacturer and is no longer available. Read More...
Eli May 06, 2021 for Model Number ehafitz@gmail.com Dishwasher Model: fghd2465nw1a The dishwasher does not drain, I bought a new pump and it worked for one cycle. Every time it goes to drain, the pump hums but doesn't seem to spin or pump. Thought about checking the volts/resistance to the pump when it tries to turn on to see if the board is properly regulating the power. Is it possible a bad board would cause this issue? Maybe a capacitor in inline with the motor would help?
1 Answer Eli, I would check the new pump to see if something has gotten down into the pump and jammed it. Read More...