Carl December 28, 2020 for Model Number PLD2850RDC2 The dishwasher only runs on the "wash bottom rack". This cycle works fine but no other buttons on the touch pad work. I have turned the power off at the breaker for 1 hour. Problem persists. Do you think I need a new touch pad or control board or something else? Thank you
1 Answer Carl, With only the one cycle illuminating then this will likely be an issue with the touchpad on the unit. Read More...
Shaun November 11, 2020 for Model Number FGHD2465NF1A Loss of power to control panel acts as if the whole thing has lost power supply. Was able to diagnose that there was power to the unit... But do remember having it shut off while in the drying process occasionaly
1 Answer Shuan, This issue will most likely be caused by a faulty control board which will be part number 5304514670. Read More...
Vicki September 29, 2020 for Model Number FGHD2465NF1A When I run the quick wash cycle the display panel shows 48 min after the door is closed, it runs to about 44 and then the display shows 99+. It happens even when I run an empty or almost clean items test cycle. I have cleaned the bottom of the machine and nothing seems to work. I also notice that the panel turns off randomly after I have selected my wash setting. Can you help me with this please.
1 Answer Vicki, With the display going to 99+ minutes and at times turning off completely while in a cycle, this would most likely be a control board issue. Read More...
Alex May 19, 2020 for Model Number PLD4375RFC3 Frigidaire Dishwasher Hi , I have a PLD4375RFC3 Frigidaire Dishwasher. It stopped working. Display is showing time for different cycles and buttons/lightssamitize/drying are functioning. No reaction of delay button (usually it shows number of hours for delay) Start button - normally after pressing, it shows time of a chosen programm and CL - for example 93CL. After closing of the door the cycle is initiated. Now when start is pressed no CL is showed, i.e. only time is displayed. So this is not a door switch. No failure messages. The water/service test cannot be initiated. I would appreicate any advice. Control board?? Thank you. Regards Alex
1 Answer Alex, It does sound as if the control may be the issue but there are also indications of the user interface. Check the connection between the two and attempt the diagnostics again and then you may need to replace the board. 5304514670 Read More...
Paul May 03, 2020 for Model Number fghd245nf1a I have and ER code which one should i replace the control panel or the eletronic control board
1 Answer Hello Paul, the control board showing that code says it cannot recognize what the control panel is telling it to do, replace the panel , part 5304480722. Read More...
Robin April 19, 2020 for Model Number Frigidaire DW model FGID2474QF3B My dishwasher will not complete any cycles; it usually just continues to run by rinsing and heating or simply stops without completion. Occasionally it throws error codes i40 and i20. The drain and filters are clear. It will not reset at the push-button controls so I've master reset at the breaker several times. At times the lights on the keypad will not come on and also the keypad controls at times will not respond to anything (unless I perform another master reset by cycling the breaker). The DW is 4-1/2 years old. It seems to me that this issue is most likely the control board. Is that correct or should I be looking at something else?
1 Answer Hello Robin, a faulty water level/pressure switch 5304504077 can cause both problem codes. Read More...
Jim August 23, 2019 for Model Number FPHD2485NF1a the Frigidaire dishwasher I'm working on gets to the heated dry cycle then flashes PF. My first thought would be the circuit breaker is getting bad and it can't take the load the heater draws, or the heater relay on the board is getting week?
1 Answer Jim, the heater could be drawing too much amperage and can be tested for resistance. The heater 154825001 should read 16 ohms of resistance. If the heater tests good, and the circuit breaker is not tripping, you may want to check the wiring connection at the terminal housing. If the wire connections are secured properly, then the failure would be with the control board 5304514670. Read More...
Ben July 31, 2019 for Model Number FDB4315LFC3 My wife reports PF code on most cycles, soap has never dispensed, and it does completely drain...always some water in the bottom. Some cycles will not go more than 2 minutes before PF code, others a little longer. Control board?
1 Answer Ben, with the power turned off to the unit, you may want to inspect the terminal box to ensure that the wire connections are not loose. Commonly what can happen is the wires are not fully secured or improperly set and over time an intermittent gap can occur from vibration. If the wires check good in the terminal box, then the most likely issue would indeed be with the control board 5304514670. Read More...
Dan April 19, 2019 for Model Number 58715203801 I found a burnt resistor on the control board. Could tell me the resistor value or send me a close up picture of R50. It's right beside the large blue capacitor. Thanks in Advance
1 Answer Dan, we would not have the resistance value of the resistor on the control. The image found in connection to the part is what we would have available. Read More...
Ron March 01, 2019 I have a Frigidaire Gallery 24 dishwasher model #fghd2433kf0 When you choose your wash cycles, all come up with a time of 99+ except the quick wash, which comes up 50. On that cycle it counts down to 44 then kicks up to 99+. Do I need a new control board? Ron
2 Answers Ron, No, you don't need the control board, at this point. The control will extend or shorten the cycles, based on water temperature and turbidity of the water. Make sure the water temperature in the tub, on the first fill of the cycle is at least 120 dgr.F. Check the wires and connections at the turbidity sensor 154762601 / 154762601 Sensor, turbidity, snap-in, w/seal in the bottom of the wash pump/sump assembly, you want to remove the sensor and check the upper portion for sediment, debris and deposits. Also check or replace the detergent and rinse aid, they may be producing suds/foam during the cycle and causing the control to extend the cycle as well. If all's OK, then replace the control board. Read More...