John September 13, 2018 for Model Number Electrolux french door with freezer on bottom Having issues with power failure faults. Intermittently thru the day! Reset it may last 5 to 6 hrs then get alarms again! Just wondering if it main be main power control board on bottom? Checked all power connections and breaker they are good
1 Answer John, first check the power outlet at the wall. Make sure the outlet is properly polarized, grounded, and 110-120 VAC. Then check the wiring and connections and replace the 5303918523 Board-Switch if all's OK. Read More...
Bobby February 06, 2018 for Model Number EI26SS55GB0 We have had the auger motor stop working in the ice dispenser. We have also lost the water dispenser function. We usually hear a solenoid fire when dispensing water but it is now silent. Are there functions of the bottom board-switch control board? I was wanting to replace this only since it is only $159.00. The front interface display appears to be functioning properly. I am told that if the issue is w/ the interface board you can't buy this separate. Just an fyi we have have had both boards replaced two times.
1 Answer Bobby, Based on the issue with the unit, this would most likely be the user interface that is the issue and would be part number 5303918584. Read More...
Angela January 14, 2018 for Model Number EW23SS65HS0 Came home to my Electrolux refrigerator in power fail mode and alarming, water on the floor, etc. I would silence the alarm and the panel clears but then a few second later it would alarm again and cycle on and off and alarm repeatedly. Finally got it back on and “working” around 8pm and at 3am the alarm was sounding and again showed power fail mode. I’m thinking the control board from what I’ve been reading. Thanks.
1 Answer Angela, Since you didn't mention any codes or erratic displays in the dispenser control panel, we would agree with you, and suspect the [AP4695229 241757001 Board-main power . It's located on the bottom of the refrigerator, behind the lower kick plate grille. The board circuitry could have failed or there may have been an electrical surge that may have damaged the control board. Read More...
Ken S December 04, 2017 for Model Number E23BC78IPSJA Old Main control board not operating defrost heater. Replaced with two new boards. Neither would power on. Old one powers on.
1 Answer Hello Ken. You are ordering the wrong board. You will need to order 5304499080 for the main board needed. Thank you. Read More...
Homer Garza September 15, 2017 i purchased from your comp a part# 5303918523. on the last step from the instructions, it tells me that the cabinet harness that connects to the J9 A1 will connect to the new board, not the jumper harness, but the is no place to plug the cabinet harness to the new board, just the connector that is attached to the jumper harness. So am i misunderstanding the last step instructions or do i just connect the cabinet harness to the last connector from the new harness? Also, on the new and old board, there is a 8 pin slender connector, (upper middle) location where the cabinet wires fit in, am I missing something or is it there just for decoration. This board is for my electrolux side by side with wave touch panel.
1 Answer Homer, The 8 pin connector may not be needed as it may be for a different model. As for the cabinet harness, look for a connector that has J9 next to it and plug in the cabinet harness there and if there is a connector from the harness attached to it then you would disconnect the jumper harness. Read More...
Laurie December 07, 2016 for Model Number Ei28bs56is5 My Electrolux French door Ei28bs56is5 is showing code ef. Replaced evaporater fan worked great for about 6 hours. Code is back. I'm guessing I need a new control board but which one?
1 Answer Laurie, The part number for that you would need will be the board switch 5304478376. Read More...
1 Answer Hello Grady. You will need to contact an HVAC tech to come and replace the line due to the Freon in the unit. Thank you. Read More...
Aid Appliances April 17, 2016 for Model Number EI26SS55GS0 Hi, I would like to change an user interface and board switch ( parts 5303918584) on Electrolux refrigerator, but when i received a parts I notice that parts are correct, but has different connector, so how can i connect connectors the old model user interface and board switch on new model .
1 Answer Aid Appliances, You will connect the unit up with the harnesses that come with the part. There should have been instructions that would have come with the part. Read More...
1 Answer Steve, With the ice and water starting on its own, this would most likely be a issue with the control board 5303918523. Read More...
Chris S. March 07, 2016 for Model Number FGHS2631PF2 My fridge had been acting up lately, the tempature on fridge used to go negative 30 in freezer but yet fridge goes like 50 degree. I had them set to 0 and 40. I have replaced both thermostat and now freezer stays right at 0, but fridge stays at 48 when its set to 40, and when i set it to 33, it actually brought temp down to 30, so i made it 34 or 35, it stays at 30ish. I am assuming that a circuit board is not working right. The door damper works fine. Which one of the board that controls the whole tempature in fridge so i can replace and bring it back to normal fuctioning, i have found 2 different boards there. It is interface circuit board part 242058232 or main power board part 242115260