Scott Jones January 08, 2021 for Model Number Frigidaire FGUS2642LF2 Food was frozen in the refrigerator compartment. Temperature display on control panel was displaying well above freezing. Replaced Themistor today however as unit cools the temp display is showing about 20F higher than the actual frig temp as checked by a thermometer in the frig. Initially thought it might be a damper malfunction, but now thinking problem is with the main board? Any advice is appreciated.
1 Answer Scott, This would be a main control board issue if the temperature showing is higher than the actual temperature. Read More...
Dale Carter August 22, 2020 for Model Number FGUS2642LF2 My refrigerator freezer is not properly defrosting. When it stops cooling I get error codes 5Y on freezer and EF on the refrigerator. If I unplug refrigerator and plug it back in, it will reset to proper codes and start cooling again. What is this indicative of?
1 Answer Dale C, Based on the information provided the 5y-ef error code indicates an issue with or between the fan motor and the control board, check the evaporator fan motor and the check wiring between evaporator fan and control board. Read More...
Rene February 24, 2020 for Model Number FGUS2642LF2 My icemaker is making ice but water seems to drip out into the tray and freeze all my ice.
1 Answer Rene, It is possible that the water valve 242252702 is not sealing correctly and allowing more water than needed into the ice maker mold. Read More...
1 Answer Hello Rene, the error code SY CF indicates the there is a communication problem between the front control panel and the rear main control board, This model being a SXS ref check the wires from the freezer door (top /bottom) door hinge area to cabinet first for any loose /damaged wiring, if ok replace the front control panel 242114904. Read More...
Rod December 19, 2017 for Model Number FGUS2642LF1 My unit has the freezer coil frozen and does not seen to be defrosting the ref has a temp of 42F and the freezer has a temp of 24F what could you suggest Thanks Rod
1 Answer Rod, For this issue you will want to test the defrost heater and the defrost thermostat to make sure that they have continuity. If this checks ok then the issue will be the control board 5303918538. Read More...
Garth October 04, 2017 I have a Frigidaire model FGUS2642LFO. Freezer defrost element reads 29.5 ohms and defrost thermostat shows continuity when placed in another freezer and no continuity when warmed. Freezer coil is still freezing up. Could it be something else? Is there something on the main board I can test with a multimeter?
1 Answer Hello Garth. Since the element and thermostat are good, you will need to order and replace the main board 5303918538 on the unit. Read More...
Tim March 23, 2017 for Model Number Fgus2642lf2 Where is control switch located on the refrigerator? Part AP4695243 I cannot find on your diagram.
1 Answer Hello Tim, The main control board 5303918538 for this model is located under the front of the refrigerator. Remove the grille and one screw holds the control box in position against the bottom of the appliance cabinet. The back of the box has tabs that fit into slots on the appliance cabinet. Read More...
Jesus S January 05, 2016 for Model Number LGUS2642LP0 When I plugged the refrigerator in,the compressor and the condenser motor turn on for about two seconds then both loose the power from the control board, is the control board going bad or is there something else that I need to check?
1 Answer Hello Jesus. Yes, it sounds like the control board is bad and will need to be replaced on the unit. Read More...
Richard December 31, 2015 for Model Number fgus2642lf1 How can I manually put switch into defrost so I can see if switch is faulty.
1 Answer Richard, To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds. Read More...
Jrebello September 02, 2015 for Model Number LGUS2642LF0 There's no power at all to my refrigerator. The outlet it's plugged into works fine. Want part do I need to replace? Thanks, jr
1 Answer Hello JRebello. You need to test for power to the main board 5303918538. If there is power there and none coming out, you will need to replace the board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...