Brandon June 08, 2016 for Model Number FAFS4272LW0 The control knob on the front of the machine to choose the wash cycle will not change cycle. What should I do? I have tried unplugging the machine and waiting 5 minutes then plugging it back in.
1 Answer Hello Brandon. Based on the information you provided, it sounds like you will need to replace the control board 137260800 in the unit. Read More...
Gary D May 31, 2016 for Model Number FTF2140FS0 How do I remove top of washer and replace control board?
1 Answer Hello Gary. There is some screws on the back of the top panel. You remove those screws from the top panel and then slide the top backwards and lift off the cabinet. Read More...
Vinh March 29, 2016 for Model Number LTF2140FS0 I have a frigidaire front load washer model number LTF2140FS0. When I turn the washer on the light come on, the door lock, but the machine does't start it wash cycle. I replace the door switch assemble but it still doesn't work. What you think might be the problem?
1 Answer Vinh, You will want to check to see if the water valve is getting 120 vac to them. If there is 120 vac then the issue will be a faulty water valve. If there is no power then the issue will be a faulty control board. Read More...
Ron March 08, 2016 for Model Number FTF2140ES3 Hello - My Frigidaire from loading washer will work on all program modes except "Normal". Any ideas? Thanks. Ron
1 Answer Hello Ron. Based on the information you provided, you will need to order and replace the control board 137005000NH on the unit. Read More...
Bruce K November 28, 2015 for Model Number 134667500 Washer runs to tumble cycle will not spin or high speed spin.Did diagnostic came up with e43 is it the board for sure?
1 Answer Bruce, With this being a Frigidaire unit, the manufacturer states with a E43 error code it will be a faulty control board and the control board will need to be replaced. Read More...
Barbara September 02, 2015 for Model Number Firgidare front load washer The main control board has been replaced. The lights all come on but the washer will do nothing. What do I need to do?
1 Answer Hello Barbara. You will need to check and make sure the water is turned on and the door lock is good on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Kathy May 30, 2015 for Model Number FTF2140FS1 The machine won't start on any of the settings (normal, heavy, permanent press, etc).
1 Answer Hello Kathy, You will need to run the diagnostics as described on the units' tech sheet. If you cannot find the units' tech sheet in the envelope in the bottom of the unit, let us know your e-mail address and we can get you a copy with no problem. Read More...
Gerry May 02, 2015 for Model Number LTF2140ES0 Wash machine beeps constantly, running or not. Lights. Flash, washes fine
1 Answer Gerry, This issue would most likely be caused by a faulty control board that has a key stuck. The part number that would need to be replaced would be 137005000NH. Read More...
Rick H. April 09, 2015 for Model Number Electrolux LTF2140ES3 Machine works intermittently. Will sometimes get through entire cycle or stop with water in tank. Machine beeps randomly without user near machine. There is a clicking sound (door lock) when it stops mid cycle. Please email me if you would like to see the video. Is this most likely the control board or the user interface? Thanks for your help.
1 Answer Hello Rick. Check and see if there are any stuck buttons on the unit. If there are no stuck buttons, you will need to order and replace the control board on the unit. Read More...
Jan R December 25, 2014 for Model Number FTF2140ES Have a Frigidaire front loader washer, just recently all the lights came on(washer not is use) pushed pause,cancel button and lights go out temporarily then come right back on. I put a load of wash in to see if machine would work and did the load just fine. Lights continue to come on whenever it sets a mind too. Had previous problem where I was losing cycles that wouldn't work and you & the dealer thought it was another control panel issue. So happened the 8 hr setting was on and when I cancelled it all my cycles work just fine.
1 Answer Jan, This issue sounds like it would be caused by a stuck keypad on the control. You will want to make sure that this is not the case and if this checks ok then the user interface may be the issue. Try to unplug the unit for 30 minutes then plug it back up. This would do a reset. Read More...