Donna November 11, 2014 for Model Number FTFB4000GS0 Cold water not entering washer, switched hoses around nothing comes thru cold.
1 Answer Hello Donna. If there is no cold water and you switched the hoses and still no cold, then the cold water supply is bad. Check the screens in the hose and the shut off for the water. Read More...
John A August 19, 2014 for Model Number ltf2140fso When plug the power in, it will only beep 9 ttimes and all the lighs flash. Have to unplug the power to get to stop. Help
1 Answer John, based on the issue it sounds like there may be a stuck key on the control board since the unit beeps as soon as power is applied. This would require a new user interface board. Read More...
Janice R August 02, 2014 for Model Number FTF2140ES2 Months ago I suddenly could not get my machine to work on the quick cycle. Then another couple of months went by and the Regular cycle wouldn't work. I can use the perm. press and the Large load cycle o.k, so far. I called the appliance store where I bought the machine in 3/06 and they said I needed a new control panel and use the machine until it died. I have had 3 previous times where I have had to have the control panel replaced. What is going on?
1 Answer Janice, The first thing that you will want to do is access the tech sheet inside the unit. Put the unit into a diagnostic mode and see if any error codes come up. If there are no error codes then the control board would most likely be the issue. If there are error codes then test the component that the code refers to. Read More...
Sharon July 30, 2014 for Model Number LTF2140FS2 Our front load washing machine will randomly start beeping. The machine still functions but it is quite annoying. it has occurred when it is washing a load and when it is sitting idle. I have read other posts and they point to the control board. Before I order the part, I'd like to be sure that is what is going on here. Thank you.
1 Answer Sharon, With the unit beeping during the cycle but the unit still operating normally then there is a fault in the control board which would need to be replaced. Read More...
Dennis W April 19, 2014 for Model Number FTF2140FS1 My washer will run through all of the cycles but will not high speed spin in normal operation. In diagnostics mode it will high speed spin and all of the tests function correctly. The only thing I get is E43 error code. I have cleared the code and tried again. It just keeps giving me E43. I have replaced both the motor control board and the front button control board and I am still getting the error code E43. I am about at my wits end ready to throw this thing off of the back porch since I have put almost $300 into it and it is still doing the same thing as when I started. Is it possible the new front control board I got is bad right out of the box or could their be something I am overlooking. Thank you
1 Answer Dennis, The E43 error code is a main control board problem in which the manufacturer states to replace the main control board. The part number for the board is 137005000NH. Read More...
Kelly April 14, 2014 for Model Number Frigidaire LTF2140ES3 Out of the blue the washer will stop .. the lights will blink and the machine will beep. We can drain it and restart it but sometimes it will run all the way sometimes it won't. After it finishes .. out of the blue it will start beeping. I have looked online and found the error codes .. It blinks 44. We replaced the door switch and it's still doing the same thing. HELP
1 Answer Hello Kelly. Based on the information you provided it sounds like a control board issue. Make sure the wiring harness is good first. Read More...
Ron April 11, 2014 for Model Number FTF2140ES0 I've read posts with similar problems as mine, which is a error code E46, Control board problem. Within any cycle when it got to the spin cycle, in just sat there after the pump removed all the water and wouldn't spin. My only beef is that when I replaced the control board (Main control board) I continued to have the same exact problem. I also read that the door switch could be at fault so I checked that and discovered that it was bad. I checked all connections and am waiting for the door swich to come. I temporarily jumpered out the door latch contact that told the processor (Main control board) that the door was shut. It spun in the spin cycle but too slowly to get the water out of the clothes. After spending over 250 dollars on parts I'm wondering if I should just abandon the washer??? Any suggestions?
1 Answer Hello Ron. You need to wait on the new door lock and see if it corrects the issue. The board will not full spin on one that is jumped out. Read More...
Mike March 24, 2014 for Model Number Frigiaire LTF2140ES3 Washer will not spin or tumble in early wash cycle, then shuts off as if done but clothes are full of water. When running the diagnostic test, the machine will tumble, spin at high speed and pumps water out. The error code 44 beeps (control panel) only after the last test. Should I trust the test and order the part?
1 Answer Hello Mike, The fault code 44 indicates a control board problem. The fault codes indicates that the fix is to replace it 137005000NH. There isn't anything other than checking for poor connections that can be done in this case. Read More...
Tom K. January 23, 2014 for Model Number LTF 2140FS1 Our washer lights on control board will flash and it beeps when not in use. It will do this for hours but then stops, then all out of the blue it starts doing it again.
1 Answer Tom, This issue sounds like there is a fault in the control board of the unit which is making the unit flash and beep. You should access the tech sheet and see if there are any stored error codes which would help with determining if the issue is the board or something else. Read More...
Washerhater January 09, 2014 for Model Number FTF2140FS0 The normal cycle on my Frigidaire washer all of a sudden doesn't work. It seems like it is starting and the door locks but it doesn't actually start. The other cycles appear to work fine. My self diagnostic gave me an error code E41 (control board thinks the door is open). If the door wasn't closed why would the other cycles run water? I'm thinking I have to replace the control board.
1 Answer Hello Washerhater. Yes, if all other cycles work fine, then the board 137005000NH is bad and will need to be replaced. Read More...