Frustrated May 17, 2017 for Model Number fafw3511kro Would not perform high speed spin. It thinks the door is open. The code is for control board replacement. I replaced the control board with reconditioned control board.The new board will not work. All program LEDs flash and only a couple of programs light up but I don't know which ones due to LEDs flashing. I received another control board but I get the same results. I reinstalled the original control board and it works fine except for no final spin.I also installed a new door switch.
1 Answer Hello Frustrated, For model FAFW3511KR0, you should pull the tech sheet and run the diagnostics to pull the fault codes. If the unit still "thinks the door is open" after the main board and door lock assembly has been replaced, there will be an issue with the wiring harness 134606800 and/or 137104600. Read More...
Zee April 19, 2017 The normal cycle on my Frigidaire Affinity front loader washing machine is set on 1 hour and 13 minutes. I guess my kids played around with it. I can't seem to find a reset option on it.. Would anyone know how to fix the timing?
1 Answer Hello Zee, I'm sorry but we will need to ask you to post a new question including the model number from your units' I.D. tag so we can recommend parts that can be guaranteed to work properly on your unit. Thank you for your patience and understanding in this matter. Read More...
Keu March 30, 2017 for Model Number FAFS4272LWD After running tub cleaning cycle when controle asked I seleected normal it will not let me select water tempriture, spin setting goes to no spin and can't select soil level it defaults to 26 minutes it was running 45 minutes all other settings work ok the machine was set on normal when clean tub came on so I just ran it. Is there a way to reset it?
1 Answer Keu, Remove power to the washer for 5 or so minutes, plug the power cord back in and perform the " FACTORY RESET 1¼”x2” display models, wake machine, push the spin speed and soil selection keys simultaneously and hold until you hear a beep. This is no more than 10 seconds." If the problem persists, or if you wish, remove the top panel and retrieve the tech data sheet,from the top panel or frame brace and review the error codes logged by the memory, and run the operational tests listed on the sheet. Read More...
Del January 27, 2017 for Model Number LTF2140FS2 Washer will not start a few drops of water will come in and it stops immediately.
1 Answer Del, You will want to check to make sure that there is 120 vac getting to the water valve. If there is not 120 vac to the valve and staying steady then the valve is the issue. If there is only momentary power to the valve then the issue will be caused by a faulty main control board. Read More...
Eric January 03, 2017 for Model Number Frigidaire ftf2140e It fills with water and agitates and drains but will not spin. Get error code 42 could the control board be the problem?
1 Answer Eric, Yes, the control board could be the problem, but first check the door latch assembly, make sure the door is latched and unlatches " Remove power from the washer. Wait one minute. Can you open the door? Yes. Replace the control board. No. Replace the door switch assembly. Read More...
Warren November 25, 2016 for Model Number FTD2150ES0 I have a frigidaire washer , the diagnostics test checked out, but machine won't complete final spin. I think our error code came up as 47. We tested the door lock assembly, it seems good, the reading was low (900 ohms) shortly after using the machine, it's now 1100, but still not around the1500 indicated for a good assembly. Not sure if that's the issue of the control board.
1 Answer Hello Warren, If your model number is actually FTF2140ES0, this is a door latch fault code. I would replace the 131763256 door latch assembly unless the model number is in fact different from the one I listed. The one you provided unfortunately did not come up as valid. If it is different, I'm sorry but we will need to ask you to post a new question including the model number from your units' I.D. tag so we can recommend parts that can be guaranteed to work properly on your unit. Thank you for your patience and understanding in this matter. Read More...
Mike D. November 20, 2016 Normal is just about the only mode that can run to completion. Modes like delicate and hand wash start to fill but never tumble. Other modes like heavy and perm press don't complete either. I checked the washer and it just has the door lock LED lit. I can then run the drain and spin mode. I ran a diagnostic test on the washer and during the test where it is supposed to fill and tumble it fills, but never tumbles. All the other tests seem to work correctly.
1 Answer Hello Mike, This sounds like an issue with the speed controller, (motor control board). If you could please post a new question including the model number from your units' I.D. tag, we can recommend parts that can be guaranteed to work properly on your unit. Thank you for your patience and understanding in this matter. Read More...
Ed September 07, 2016 for Model Number FTF2140FS1 The unit will not drain. I've run the diagnostics as per the manual and get an error code that refers to the pump. I've checked the pump with a continuity meter and it shows no break. I've also cleaned out any clogs and the unit still won't drain. I believe the problem is the main control board but is there some way to check the main board? Does your site have a video showing the replacement? Thank you.
1 Answer Hello Ed. Yes, you can check the board. You need to test for power from the board to the pump. If it is there, then the board is fine and the pump will need to be replaced. A continuity test on the pump is not a definitive test. A power test is a great test. Sorry we do not have a video at this time. We are working daily at adding new videos to our site. Read More...
Alan July 18, 2016 for Model Number FTF2140FS1 Frigidaire washer control board. I have FTF2140FS1 s/n XC74914985. Current board is labeled 134667500. Error code is 44. Is 137005000 compatible replacement ? Thanks
1 Answer Hello Alan. Yes part number 137005000NH is the correct control board for your model. Read More...
Steven J June 09, 2016 for Model Number FTF2140ES I'm trying to determine which part to buy to repair my front loading washing machine. My Frigidaire front loading washing machine FTF2140ES ( year 2006 or 2007) blinks as follows, however I cannot interpret the code could you please help ? After pressing the start and cancel buttons, I get 2 blinks of the start light and 2 blinks of the other 5 lights at the same time, then there is a longer pause followed with 4 blinks of only the 5 lights. What does it mean ?
1 Answer Hello John. You will need to check and make sure the unit does not have any stuck buttons and make sure the lock is good. If so, then it sounds like the control board will need to be replaced on the unit. Read More...