Judy February 01, 2014 for Model Number atf6000es frigidaire washer When I press start the washer appears to act normal. The water starts to come in for about 10 seconds then the washer goes from 31 to 28 minutes and does nothing. The lights all remain on but no error code and it wont continue with the cycle.
1 Answer Hello Judy. You will need to check the main board in the unit. If it is skipping cycles, it is bad. Read More...
Luis January 14, 2014 for Model Number 134409904 I have an washer affinity Frigidaire that seen to be that the motor control board is no good, so I came to your website and when tipping the number of my part in order to find my right part the system give another number and I am not sure about if this an replace part that is compatible with my washer. regards
Rich December 30, 2013 for Model Number LTF2940ESO Hi, I just purchased the control panel last night. Looking at the diagram, I really can not see where the control panel will be? Is it buried in the washer, or when I remove the top panel I will be able to see it? Thanks Rich
1 Answer Rich, We attempted to send you some additional information you may need, but the e mail was returned as a "mailer-daemon@googlemail.com" The email account that you tried to reach does not exist. Please try double-checking the recipient's email address for typos or unnecessary spaces. If you still need our assistance, please repost the information using a proper e mail address. Thanks Read More...
Randy C December 10, 2013 for Model Number GLTF2940FE1 Frigidare front load washer will not let any water into drum. Will not let water out. What could be wrong?
1 Answer Hello Randy. If full, it will not fill with water. You need to check the pump and see if it is bad or clogged in the filter. Read More...
Mc December 02, 2013 for Model Number gltf2940fs1 Fridgidaire front load washer PN gltf2940fs1 is not filling up with water. Front panel lights up but will not initiate further. Checked water, ok. Finally got it to spit out an error code (E56) Checked the motor coil resistances, all were between 5.5 and 5.7 ohms. Problem started with 1 min left in a wash cycle. Any ideas.
1 Answer Hello MC. The error is for high current. To make sure of whether it is the motor or the motor control You will want to do a resistance check between pins 4 and 5 in the motor. If the resistance is between 105 and 130 ohms then you will want to Disconnect the plug from the motor and measure the resistance of the windings. Pin 1 to 2, pin 1 to 3 and pin 2 to 3. All readings should be between 4 and 6 ohms. If the readings are correct then replace the speed control board. If the readings are incorrect then replace the motor. The board can be accessed from the front of the machine in order to get it out. Read More...
Bob P December 01, 2013 for Model Number gltf2940eso No error shown does not run full cycle stops when to spin rinse, must shut machine down, manually set at end for rinse spin, can only run on quick load, 32 min
1 Answer Bob, Based on the description, this issue sounds like it would be caused by a faulty control board. You will want to check to make sure that there are no clogs in the drain that could be causing the unit to not finish the cycle. You can also access the tech sheet on the unit and run a diagnostic which you can then see if there are any stored error codes. Read More...
Eric S November 04, 2013 for Model Number GLTF2940ES0 My washer is filling for approx 1 second, and then doing nothing after that. It is giving me a E5E code. Would the control board be the part I would need to replace?
1 Answer Hello Eric. Communication problem. If all wiring is good, you will need to replace the control board on the unit. Read More...
Doug November 03, 2013 for Model Number ATF6000FS0 Washer is not performing spin cycle properly, diagnostic mode provided error code E47. States there is a potential problem with defective door lock assembly or defective control board. I do not have an ohms meter to test resistance today. While reading through some question presented by others, another gentleman was having the same problem and he was told to make sure the pump or the filter between the drum and the drain line were not plugged. How do I check the filter bewteen the drum and the drain line that goes to the pump?
1 Answer Doug, The filter 137518800 is located inside the tub to pump hose 134455900 You'll need to disconnect the hose from the tub drain opening to check it . The E47 code does indicate an issue in the door lock assembly 131763256 and you'll need to check for 1500 ohms across the wax motor terminals. if all's OK you'll need to check for loose connections and wires then, replace the control board 134743500. Read More...
Dan October 31, 2013 for Model Number 41748102701 Hello, On any cycle, as soon as I push the start button, either of two things happen, either the spin indicator light immediately goes to "No Spin" and you hear a humming sound, possibly the drain pump. or the "Door Locked" indicator light goes on and the "No Spin" light goes on and then the humming from the drain pump. I do get the error code E45 but don't know which control board to replace? the 137005010 board or the pump motor control board 134743500? thank you for your help.
1 Answer Hello Dan. Check the pump for clogs first and make sure the pressure switch is good. If so, replace the board 137005010 on the unit. Read More...