Christopher October 06, 2019 for Model Number fafs4272lwo I just replaced a leaking tub to pump hose. After replacing I ran the clean cycle. Tub filled with water, ran through the cycle and then stopped with 8 mins left. Tub did not drain. When I try different cycles it just continues "sensing". I removed the hose and didn't find any kinks or obstructions. Replaced the hose and still have the same problem. Didn't have any issues before I replaced hose. Getting error code E32. Tech sheet says pressure sensor or main control board. Could it be anything else?
1 Answer Christopher, I would disconnect the pressure sensor hose at the pressure switch and blow through it making sure there is no blockage. Next, you can do a continuity test on the harness between the pressure switch and main control to make sure no wires are damaged. The pressure switch should have a three-wire connection with white being a common and black and blue reading the full or empty status. A continuity test on these wires should tell you if the pressure switch is reading water in the tub or not. Read More...
Mark March 26, 2019 for Model Number FAFS4272W0 My Frigidaire Affinity Front load washer doesn't take enough water to wash or rinse, even after i select deep fill option. I had already replace the water level switch and I still have the same problem. I need help.
1 Answer Mark, you may want to check the filter screens on the inlet valve [134637810]. Another thing to check would be to ensure that the pressure hose does not have any thing in it. If you run the washer when empty, if you have a lot of suds appear this can cause pressure build up that will influence the operation of the water level switch. Read More...
Paul July 13, 2018 for Model Number FAFS4272LWO I used the normal wash cycle the most. Now it quit working. Displays 26 minutes wash and no spin. Lights on auto temp, soil level and options will not come on to make a choice. The other wash selections still work. What part would fix the problem?
1 Answer Hello Paul, You should use the tech sheet to pull any saved fault codes. The most common failure on this design is the door lock 131763256 and the motor control board 134618213. The fault codes will tell on the issue. Read More...
Rudsok September 12, 2017 for Model Number FAFS4272LW0 close washer put in rinse cycle and all I hear is a clicking sound should I replace the board
1 Answer Rudsok, Not yet, first check that the door is aligned and closing properly and the door latch assembly locks the door, Then check the cold water faucet and fill valve to make sure there is water supplied and flowing into the washer, first. Read More...
Vanessa March 19, 2017 for Model Number FFFW5000Q0 frigidaire front load washer This machine is stuck on pause after every possible part was changed. What can be the problem. Door lock, wire harness motor control board circuit board control board and another door lock.
1 Answer Vanessa, Check for a stuck button on the control panel. Then remove power, then the top panel, then the control pnel assembly. separate the control board 809055505 / 137035252 from the control panel and check for damaged or stuck buttons and the plastic return spring assembly for damage. then replace the control board if all's OK. Read More...
Hansen July 01, 2016 for Model Number FAFS4272LW0 Hi. Is it possible that I would get error code E 9F MB-FCV COMM due to a power surge or power draw that sometimes resulted in machine turning off? Or is it just control panel? Thank you for your assistance.
1 Answer Hansen, While it is possible that a surge could have caused this error, you will want to check the wiring harness between the main control board and motor control board. If the wiring is bad then correct the wiring issue. If the wiring is good then replace the main board and if this does not correct then replace the motor control board. Read More...
Sue June 28, 2016 for Model Number fafs4272lwo Hi. Can error code E9F MB-FCV COMM be caused by any fluctuation with electricity?
Rick January 15, 2015 for Model Number FAFS4272LWO The washer will not drain on spin cycle or any cycle. I have bench tested the drain pump good, clean out all filters and hoses. Checked door switch good, checked motor board good. Replaced pressure switch. It spins up to 6 minutes then gives an error of E 35. Main Control Board is this the problem ? and needs replaced ?? Thank you. Rick.
1 Answer Rick, the E35 error code indicates an issue with the pressure switch, since you've replaced it you need to check the air tube from the pressure switch to the drain pump connection. Make sure the tube isn't kinked, twisted, clogged or has a pin hole. If all's OK then replace the control board. Read More...
Carlos January 15, 2015 for Model Number FAFS4272LAO My washer doesn't spin. When I checked for codes it gave E38 which, last option is to replace board. I've done everything else but replace pressure sensor switch, which I think is okay. So should I replace the main board? At first it wouldn't let me open the door after disconnecting it. It let me open but everything was soaked. Put to spin only and moved back and forward very slowly.
1 Answer Hello Carlos, the motor control board 134618213 is the first suspect. You can, of course, pull the tech sheet and test the motor windings first to eliminate the spin windings as an issue. Read More...
Nick June 12, 2014 for Model Number FAFS4272LWO Washer says door open. Checked striker looks fine. Replaced door switch...not problem either. Replaced control board PN: 137260800. What else could it be? What about this PN: AP5628646? How can I check before buying and returning parts? Thanks for your time.
1 Answer Hello Nick. If the board and the lock assembly are new, you will need to replace the wiring harness on the unit. Read More...