Amy September 21, 2021 for Model Number ffef3048lsd Looks like maybe one of the mounting tabs for the display has broken, do I have to purchase a whole new control panel or just the overlay. Everything on the panel works fine it's just the overlay is pushed back on one side.
1 Answer Amy, if the overlay is able to press into the control housing, the control 5304509493 would need to be replaced. This would also be the case if the mounting points of the control housing have broken. Read More...
Marsha August 04, 2020 for Model Number FEFL68GMH My clock seems to have dropped with nothing holding it but everything still works fine
1 Answer Marsha, this happens often. The mounting tabs on the control have broken. You would need to replace the control part number 5304509493 and overlay 316419141. Read More...
Marsha May 18, 2020 for Model Number FES365ECE I am looking for the plastic piece that covers the push buttons on the control panel. Is this the correct part?
Tony August 12, 2018 for Model Number FEF366EBB When selecting the oven I believe the broiler comes on and burns my pizza to a crisp. I had f10 code. what part do I need?
1 Answer Tony, For the F10 error you will want to test the oven sensor for resistance of 1090 ohms at room temp and if this checks ok then the control board would need to be replaced. The F10 means a runaway temperature. Read More...
Asif M. January 23, 2018 for Model Number FFGF3053LS The gas range is displaying the F10 code. The cooktop works, but not the oven. What is the part number for the EOC or the RTD? How can I tell if the Electronic Oven Control (EOC) board or the Oven Temperature Sensor (RTD sensor) needs replacement?
1 Answer Hello Asif, The temperature sensor can be tested with an ohm meter. It should have a resistance of 1090 ohms at 77 degrees and would add 2 ohms for every 1 degree of temperature increase. If it tests good you will most likely have a bad EOC. Read More...
William March 17, 2017 for Model Number FEF366ECE The up button will not go up. All the other buttons work but when you mash the up button it just has the - and will not work. Will a new overlay work or will I have to buy the whole circuit board?
1 Answer Hello William. Based on the information you provided, it sounds like the control board 5304509493 is bad and will need to be replaced on the unit. Read More...
Erid T March 03, 2017 for Model Number FGF366EMC My panel control is not working correct I'm put tha clock for one seguen is on ant them is off everything is on for aseguen and them is off it is wy all tha control panal,
1 Answer Erid, The most likely cause for this issue would be a faulty control board 5304509983. Read More...
Sharon November 29, 2015 for Model Number 79096419400 Oven turns on, set temperature at 350°, preheat light will turn off at temperature, but temperature keeps going up. When I placed an oven thermometer on rack it went up to 600°F, oven does turn off. But cannot control temperature. Thanks
1 Answer Hello Sharon, If the temperature sensor 316490001 tests about 1100 ohms of resistance at about 70°F, the issue will be the clock/timer 316557245. The overlay 139091301 may be necessary if the clock/timer is replaced. Read More...
Willie S October 28, 2015 for Model Number FEF368GCE What is the wiring sequence for the single wires on the short side of the control panel?
1 Answer Willie, On the control board, the top terminal that has bake on it would have the yellow wire, the broil which is the second terminal from the top will be blue, 3rd terminal down which is L1 will be black, L2 out which is the 4th terminal down is Orange, and L2 In will be the bottom terminal and is red. Read More...
Harry April 17, 2015 for Model Number FGF368GMB On the "Oven Control Board", part #20, the plastic "ears" that the screws run thru to mount it to the Bracket, part #23, have broken. The electronic board snaps out of this holder but the only part I see is the complete assembly for $113. All I need is the plastic mount. Can I order this separately. Note: I do not need the metal bracket #23.
1 Answer Hello Harry, I'm sorry but the manufacturer has not made the bracket available without the board 5304509983. Read More...