Art March 06, 2013 for Model Number 417 44052400 If the water pump is bad will that keep the washer from spinning?
1 Answer Hello Art. Yes, if the water does not pump out, the unit will not spin properly. Read More...
Rob February 19, 2013 for Model Number FWSB55RGSO Frigidaire Crown Series Washing Maching. Model# FWSB55RGSO Question: After setting timer & "Load Size" for either "whites" or "Colors" the water fills normally but before the actual wash cycle starts, it starts to drain half way then fills again until I lower the load size, then starts to wash. What could be the problem. Thanks.
1 Answer Hello Rob. You need to make sure the water is not siphoning out of the unit and test the pressure switch 134680100 and timer on the unit. Either part will cause the issue you are having with the unit. Read More...
1 Answer Hello Alan. Here is a link to help you. You will log into the account here and start the return process. https://www.appliancepartspros.com/login.aspx?ReturnUrl=%2faccount%2freturns.aspx Read More...
Robin T January 19, 2013 for Model Number Frigidaire washer top load older type Last few days making a squeeking noise and this morning doing the wash water was all over the floor before the rinse cycle and after the rinse cycle. All the emptying water was going all over the floor. Checked the two hoses going to and from the pump neither was stopped up. Are there any other hoses to check, or do you think that it can be the pump? Thank you, Robin.
1 Answer Hello Robin, Based on the information, you check the only hose and the pump would be the only thing that would cause the leak aside from a leak in the tub. Check the tub for cracks or worn marks. If good then replace pump. Read More...
Chris January 15, 2013 for Model Number ATF7000EGO My front load washer is not draining the water or spinning. Could it be the pump?
1 Answer Hello Chris, The most common issue with this model is the filter 137518800 inside the tub-to-pump hose 134455900 gets clogged with lint, change, and other debris from the wash. The hose has to be removed to access this filter and it absolutely must be put back in after cleaning it unless you want to buy a new drain pump the next go around. Read More...
Sharon January 09, 2013 for Model Number GLTF2940ES3 Need to gain access to pump (part#AP4359998). Can the lower front panel be removed to do so?
1 Answer Hello Sharon, To gain access to the pump you can remove the front panel to do so but it may be necessary to pull unit out. Read More...
Jorge December 29, 2012 for Model Number glet1031fs0 Hello, my drain pump is new, but it does not start, I checked the connector in both lines is live no ground, I checked as well the cables and I do not see any broken or connected what can it be?
1 Answer Hello Jorge, You will want to check the circuit at the control. Check between connector P3 pin 6 and pin 8. You should have a resistance of 26 ohms. If you do not have 26 ohms then the pump is faulty. If you do have proper ohms then the control is faulty. Read More...
Roger December 25, 2012 My washer works on all cycles but on spin it drains all water onto the floor. What could be causing this?
1 Answer Hello Roger. You need to look for a bad hose on the unit. If all of the hoses are good, check and see if the pump is leaking. Also, make sure the drain pipe is not backing up and spilling into the floor. Read More...
Stanley December 25, 2012 for Model Number fwx833as2 When it cycles to drain, water doesnt drain. Is there a screen or filter to check before replacing pump?
1 Answer Hello Stanley. No, if the pump does not run, and there is power to it, you will need to order a new pump 137221600 for the unit. Read More...
Bryan December 21, 2012 for Model Number FAFW3577KW1 My dryer took on some water from the flood. It was on a pedestal so it didn't get too bad. Anyway, what happens is I choose my washer settings and press start. The water starts to fill for 3-5 seconds and then stops. Your tech Jordan reccommended starting by only replacing the water inlet valve, so I did. I still had the problem so I then ordered a new pressure switch, control board, and door lock assembly. All items were replaced. The washer is still doing the same thing. I just placed my fourth order with your company for a new drain pump assembly and motor speed control board. I don't know what else to do. The error code I was originally getting was E38 so that is why the tech reccommended a new pressure sensor. After replacing the control board the code I was geting was E59 No tacho signal for 3 seconds which means it could be the motor. I checked all connections on everything and the most recent code says E5E which is communication problem and it reccommends to replace either the control board, which I already did or the speed control board. So I just ordered a new speed control board and drain pump assembly. Can you please help me? I have soo much money tied up in replacement parts that I could almost go out and buy a new washer. This one is only 1.5 years old. Thank you for your help.
1 Answer Hello Bryan. When a washer is damaged in a flood, it can cause all the parts on the unit to need to be replaced. If the new parts ordered didnt fix anything, you may need to replace the motor on the unit. Read More...