Kevin September 08, 2015 for Model Number FRS24WSGW6 Should the plug coming from the ice maker to the water solenoid valve have continuity when checked with a multimeter ?
1 Answer Hello Kevin. The power wire to the valve from the icemaker should have continuity. Read More...
Kent August 03, 2015 for Model Number FRT18KG3CW2 Hi: I just added the IM15 icemaker kit to a Frigidaire FRT18KC3CW2 refrigerator. The icemaker works and seems to cycle properly for the first few batches of cubes. However, when the water valve cycles, the water volume/pressure is high enough that a portion of it overflows and splashes out of the fill cup and drains into the ice bucket. It still makes ice cubes, but I end up with a solid block of ice in the bucket. I originally installed a braided steel icemaker supply line and thought perhaps it was delivering too much water. I replaced that with 1/4" copper per the installation instructions but the problem persists. Any ideas?
1 Answer Hello Kent. Remove the cover on the icemaker and adjust the cube size down some and see if this stops the over flow issue. If not, the pressure to the unit may be to high and you will need to reduce house hold water pressure. Sometimes turning the water shut off half way closed will help with this also. Read More...
Jing August 01, 2015 for Model Number FRT21LR7ABS I have a Frigidaire FRT21LR7ABS with a factory installed icemaker Type GD-21. How does one install an icemaker water filter to an existing Frigidaire icemaker? thanks.
1 Answer Hello Jing, You can add a filter before the water line gets to the unit with the TJ60461N filter kit, and flex line TJ9SSIM1. Read More...
Tim July 10, 2015 for Model Number frigidare frs26zrg I have water coming out of the connection on the back of frig. for the water line on the ice maker when it calls for water to make ice. the line is not cut what can be the problem.
1 Answer Hello Tim. It sounds like the fill tube is frozen and will need to be thawed out on the unit. Read More...
Jane D June 21, 2015 for Model Number FRS234CWO manu 6/03 The model number on my ice maker is SA8868. This looks about the same are you sure i will fit. If I order it and it doesn"t fit can I send it back?
Rich April 22, 2015 for Model Number frs26h5asb6r Hi, I tested the motor and found out its bad. Could I just purchase motor instead of whole ice maker? Thanks.
1 Answer Hello Rich! Unfortunately, the manufacturer no longer offers the motor as a replacement and the icemaker, 5303918277, must be replaced. Sorry about that! Read More...
Bajadeek April 04, 2015 I have a whirlpool top side wrt18hbhlpoo, the ice trough is leaking water inot the ice bin, is it part of the icemaker or separate? Also the ice maker part# came up as as frigidaire model?
1 Answer Bajadeek, The model number listed is not coming up as a valid model. Please recheck the model number of the unit. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
B.D. March 14, 2015 for Model Number DGUS2645LF6A The ice chute door doesn't close. Warm air comes up into ice compartment and freezes up the ice compartment.
1 Answer Hello B.D., This is normally corrected by replacing the dispenser module 242074223. Read More...
Ben January 24, 2015 for Model Number PLHS267ZAB4 I want to replace the whole Icemaker can you please give me the correct part # I need to do this for the model fridge I have? It is a frigidaire side by side model # PLHS267ZAB4.
Ed January 19, 2015 for Model Number Gibson GRT 18S6A What is the correct replacement ice maker for this refrigerator?
1 Answer Ed, if you are needing a complete add on kit you'll need to use part number IM116000. If you added the IM15 icemaker originally to your model the replacement icemaker is part number 5303918277. Thanks. Read More...