Cathy March 25, 2015 for Model Number ATF6000ES1 Tub fills with water when not in use, then when I go to throw in laundry and open the door, water pours out. What causes this and how can it be fixed?
1 Answer Hello Cathy, This is a bad water valve 134371220. It is weeping the water into the machine past the water valve seal. Read More...
John R December 15, 2014 for Model Number FWFB9100ESO When left without use for a while the washer fills up with clean water when turned off. Water inlet valve or pressure switch which is more likely thanks
Al December 04, 2014 for Model Number GLTF2940FE0 I have error code 32, pressure sensor. The door lock light is not on. It doesn't come on after unplugging. If I try to run diagnosis the light doesn't come on. How do I check the pressure sensor? Is it the same as the pressure switch? I replaced the door lock switch with no improvement.
1 Answer Hello Al, It the unit is giving the fault code until it is put into diagnostic mode, the problem is most likely not in the pressure switch 134762000but in the control boards' 137006000 diagnostic circuitry. Read More...
David September 15, 2014 for Model Number FAFW3517KR1 My washer will not start or do anything I checked for error codes and e31 popped up this is the pressure switch not communicating code. Should I just replace the switch or what should I do? Please and thank you for your time.
1 Answer Hello David. Based on the error code, you will need to order and replace the pressure switch on the unit. Read More...
Joi H. August 19, 2014 for Model Number ATF6700FS1 Washing machine is going through the motions of working, just not filling up with water. There is no error code. The timer counts down like it is working, just no spinning or water. Have replaced the water valve intake, thinking that was the problem, but did not take care of it. All hoses and drains have been checked, no clogging or kinks.
1 Answer Joi, You will need to check or replace the water level switch 134762000 and hose 137089000. If the switch is stuck or the hose is clogged with sediment or debris. the control "thinks" the tub is full of water and won't fill. Read More...
Juan October 07, 2013 Where can I get the instructions for replacement, I found this part unattached inside of the washing machine and I want to see if I need to replace it or if I just need to put it in the correct place.
1 Answer Hello Juan. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Carol July 14, 2013 for Model Number Type III-07 CY1430691 We have a Crosley Washer, Serial # CAWS0234VQD, purchased in 2009. The cold water will not shut off. The washer goes through the cycles fine, but you must shut the cold water off manually at the shut-off valve between the wash and rinse cycles. Any suggestions?
1 Answer Hello Carol. You will need to order and replace the water valve on the unit. The model number you provided is not working to look up the part. Read More...
Ashley May 26, 2013 for Model Number LAFW3511KB0 I have a Frigidaire Affinity washer that randomly will stop mid-cycle. I get an error code e-11 ( fill time too long). I have done all the steps in the troubleshooting guide, I get to step # 7, it says to replace the pressure sensor, if this does not correct problem replace control board. I can't find a pressure sensor on your website or any others. Where do I get a pressure sensor?
1 Answer Ashley, The part number for the pressure switch for your washer is 134762000 (Control Panel heading, part #17) You also want to check or replace the air tube/hose 137089000 . We take for granted you've already check for plenty of water pressure and flow at the faucets, and checked and cleaned the debris screens in the end of the fill hoses and inside the water valve connection. Read More...
Jeff May 03, 2013 for Model Number ATF6700FS1 Help! The washer will not fill. Controls seem to act normaly and the door locks but I just get a small 'click' instead of water. I've replaced the inlet water valve assy and the door lock assy. Error code is E75 - Water temp sensor circuit. I think the temp sensor is in the inlet valve assy and i've already replaced that. What next? I need a little direction. Thanks guys
1 Answer Hello Jeff. If there is no power going to the valve, and the door lock is working, you will need to replace the control board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
John February 20, 2013 for Model Number GLTF2940FS2 Washer when started makes a humming sound but no water. It will then start to tumble, stop, tumble,ect, but no water. This seems normal except for the fact there is no water. The humming seems louder than normal I assume thats because there is no water. There is water getting to the machine and the screen at inlet seems to not have any debris. Any thoughts. Company suggested pressure switch or control panel. Dont know how to determine which one, or if either one is the problem. Thanks.
1 Answer Hello John. If there is power to the water valve, and no water, and the screens are not clogged, you will need to order and replace the water valve on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...