Kasey May 18, 2013 for Model Number PS1481889 Which wire goes where when installing the dispenser? Red in front, White in back? I had to wait on the part and forgot which way the two went.
Edward B February 02, 2013 I have a GE dishwasher Model No. GHDA656L15ss and need to replace Part No. WD12X10205 Do I need to remove the inside cover of the door in order to unscrew the old part and replace or is WD12X10205 a shrink fit. If removal is necessary, is it a difficult operation. Thanks
1 Answer Hello Edward, To replace the dispenser assembly you will need to remove the screws holding inner door in place. Once removed you will lift inner door and making sure that the power is off to unit, disconnect the wiring and remove the old dispenser and install new. Read More...
Sil January 06, 2013 for Model Number GE Profile dishwasher PPW9980N00SS The maual soap dispenser is not latching, so door remain open...dosen't seem to have any thing wrong with it that I can see. So does that mean I should replace whole dispenser and is that something that can be done simple or do I need to get a professional to replace it? In the meantime if the soap tablet is in the bottom of the dishwasher can my dishes still be cleaned? I do have the smart dispenser as well but I hear those can clog up your pipes...HELP! :)
1 Answer Hello Sil, If the dispenser door will not latch then you would want to replace the dispenser assembly. In order to change out you would remove the screws around the inner door and lift the panel. Disconnect the wiring and remove the dispenser and replace with new. The dishes will still get clean with the tablet at the bottom but it is putting it in earlier than normal. Read More...
Joe January 01, 2013 for Model Number GE PDW9980W00SS What is the model # for the Manual detergent dispenser and how I change the broken one?
1 Answer Hello Joe, The detergent dispenser for unit is part number WD12X10163. To access the detergent dispenser first disconnect power from unit. Remove the screws holding the inner liner in place. Lift inner liner and disconnect the wires to the dispenser. There will be 1/4" screws that you will remove and dispenser will come out. Reinstall in reverse. Read More...
Toby Sperber December 01, 2012 We lost the rinse dispenser cap for a GE Adora dishwasher. Can the dispenser cap be purchased separately?
1 Answer Hello Toby, we do have the rinse dispenser cap WD12X10122 available. You might want to get a spare just in case it happens again. Thanks! Read More...
Ann November 29, 2012 for Model Number GSD6600GOOWW Replacing #WD12X10237 (soap dispenser). Wires both came off at once so I don't know the order to replace the wires on the new part. Which goes where? Which color wire should be closer to the inside of the machine and which on the outside edge? Please help! Thank you!
1 Answer Hello Ann, Since the wax motor is not polarized, the order the wires go on is of no consequence. They can go on either way and the dispenser will operate normally. Read More...
Joe November 06, 2012 for Model Number GE PDW8200 The soap dispensor does not work. How do I replace it?
1 Answer Hello Joe, Disconnect power, there are screws on the inner door that you will have to remove. Once you remove inner door panel then you will disconnect the dispenser assembly and remove. Reinstall in reverse order. Read More...
Iosif October 19, 2012 for Model Number PDW7880G00SS 1. How do I remove the old and install the Rinse & Cap Module WD12X10237? 2. What is the return policy? Thanks
1 Answer HI. We have a 365 day return policy. This replacement is easy. Remove the inner door screws and separate the inner /outer door. Reach into the inner door and disconnect the dispenser part # WD12X10163 electrical connectors. Remove the screws that mount the dispenser from the inside. Exchange the new part. Re install the parts removed and reconnect the electrical. Make sure the inner door dispenser gasket is sealed flat and correct for no leaks. Thank You. Read More...
Charlie October 12, 2012 for Model Number GSD6600G00BB How do you remove the old part and install the new part?
1 Answer Hello Charlie. You will need to disconnect the power going to the unit. Then remove the inner door panel and gain access to the back of the dispenser. Remove the screws holding the dispenser in place and the wires going to the dispenser. Reinstall with the new dispenser WD12X10163 in reverse order. Read More...
Karla August 31, 2012 for Model Number PDW7300J00BB The only part that broke is the clasp/plastic "hook" that keeps the dishwasher module closed so the detergent doesn't spill out, can I just buy that part?
1 Answer Hello Karla. No, you need to order and replace the dispenser assembly WD12X10163 in the unit. Read More...