Gail May 18, 2014 for Model Number WDSR2080D5WW My Machine has been malfunctioning, When I start a cycle the water does not fill, My machine immediately begin agitating (washing), but when I turn the load bottom from quickly from large to small it starts filling, but then it just wash right through it doesn't refill through cycles, it doesn't rinse or spin, just wash & drain at the end. Why is this happening? WDSR2080D5WW
1 Answer Gail, This issue sounds like it may be a couple of things going on. The first would be a bad pressure switch causing the unit to sense that it is still full and when you switch it from large to small and back it allows it to work. The second would be stuck contacts in the timer. Read More...
Ronald C April 02, 2014 for Model Number wwa8800rblwh My washer is having problems agitating. It pumps water fine and will spin. When I looked at the drive components I found a heavy lubricating grease like substance ( molybdenum ?) had been deposited all over the place. I cleaned off the drive pulleys and belt And tightened the belt.. But the agitation is not consistent. I believe this is a pattern failure. Does this mean the transmission has failed? Can it be repaired? If so what parts would be needed? Thanks
1 Answer Hello Ronald. The part you are needing, WH38X53 has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Marie March 26, 2014 for Model Number WSERR417FOWW My washer stopped spinning for large loads. It will only spin now with a few articles of clothing. Does the driver belt need to be changed or is it something else?
1 Answer Hello Marie, This sounds like the clutch is worn. You will need to replace the motor WH20X10019 to correct the issue. Read More...
Joev October 28, 2013 for Model Number kenmore 70 series model 110 82870120 When running I get a burnt smell. Does the washer have a belt because I looked underneath and I didn't see one. If so would it need replacing?
1 Answer Joev, This unit is a direct drive in which the motor mounts directly to the transmission. The motor coupling attaches between the 2 to allow them to work together. You will want check the motor coupler 285753A to make sure that it is not wearing or becoming damaged. Read More...
Joev October 28, 2013 for Model Number kenmore 70 series model 110 When washer is running I get a burnt smell. Is this the belt needing to be replaced?
1 Answer Hello Joev. We will need your full model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Jay October 19, 2013 I have a front load washmachine that when it goes into the spin cycle sounds likes its going to take off. I marked the drive belt and it did slip could a bad belt cause this?
Lyle October 15, 2013 for Model Number WCXR1070A1WW My Washer Spins, Agitates and drains ok. About a month ago, when it goes into the Spin Cycle it sounds like a jet engine running up. Very Noisy.
1 Answer Lyle, This issue would be caused by a bad spin bearing on the tub which will need to be replaced. Read More...
Juliaeph July 20, 2013 for Model Number wbse3120b1ww My washer wont spin, the belt will not spin. Everything else works what could it be?
1 Answer Juliaeph, You will want to check to make sure that there is nothing caught in between the tubs that would cause the unit to not spin. Check to make sure that there is power getting to the motor when the unit is calling for the motor to spin. If there is power and the motor is humming then disconnect the belt and see if the motor turns. If it does then the brake of the unit would be the issue and you would need a new transmission. If there is power but the motor does not turn with the belt off then the motor is bad and would need to be replaced. Read More...
1 Answer Lorene, the belt or motor would not be the issue. It's more likely an issue in the timer switches WH12X929 or the pressure switch circuit is not "closing" between terminal 7 and 16, completing the circuit to the motor in the agitate cycle. Read More...
Devaunce April 07, 2013 The motor is is running. The machine drains but doesnt agitate. What could the problem be?
1 Answer Hello devaunce. Check the drive coupling on the unit. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...