Kimberly February 26, 2013 for Model Number wjse3110a0ww My washer is working fine except for the spin cycle, When it comes time to spin it drains but does not spin, and we smell a burning rubber smell. Do I need to replace the belt? I was going to order one tonight but need to know if this is what I need.
1 Answer Hello Kimberly. Check and see if the belt is burnt on the unit. If not, you will need to turn the pulley by hand and see if you can manually spin the tub assembly. If it will not spin, you have a bad bearing/transmission in the unit. Read More...
Sire C January 27, 2013 for Model Number WCSR4170DAWW What cause my GE washer not to agitate, spin but can drain water.
1 Answer Hello Sire, You will want to check to make sure that the motor WH20X10019 is running and that the belt is not broken WH1X2026. Since the pump is a separate part the unit will drain without agitation or spin. Read More...
Eddie December 31, 2012 for Model Number WDSR2080GWW Why won't washer agitate? Everything else works fine, draining; spinning, etc. Timer goes through cycles correctly, only no agitation during wash and rinse cycles.
1 Answer Hello Eddie, This issue sounds like either a agitator coupling or bad transmission. Read More...
1 Answer Terry, your model uses belt part number WH01X10302. You may need the belt installation tool, part number WX05X20641 to install the belt. Thanks! Read More...
Vince December 11, 2012 for Model Number WCVH6260FWW Can you let me know if the drive belt featured on your site fits the model number provided for my GE Front Loading Washing Machine?
1 Answer Vince, no part number WH1X2026 is not listed for your model. According to your model number the replacement belt is part number WH08X10024. Thanks! Read More...
Shonnie P October 04, 2012 we have a roper. day before we smelled something like it was burning when it was spinning at the end of the cycle. last night we put a load in and it filled but did nothing else. this morning the washer would not come on at all. well it would make a noise like a hmmm but in a minute it quit that also. is it the motor to the washer or is it the belt. i did not have the model number, but could get it. yesterday we went ahead and washed a load of clothes but all of the water did not spin out.
1 Answer Shonnie, Since this is a "Roper" washer, it's probably a "direct drive" washer, it would not have a belt. The issue could be an article stuck in the pump, bad timer or faulty motor. We'll need a proper model number from the serial tag, in order to assist and advise you properly. Thanks Read More...
Jj July 06, 2012 for Model Number WHDRE526E1WW Washer will not agitate..only slightly moves......can hear motor running
1 Answer JJ, you most likely have a slipping belt. Remove the front panel, loosen the four motor mount bolts and slide the motor towards the center and remove and check the belt for excessive "glazing" and slippage, grasp the transmission drive pulley, and turn it several revolutioons in each direction. It shoukld be relatively easy, If so, replace and adjust the new belt WH1X2026 . Thanks Read More...
Donna June 15, 2012 My washer drains and spins but it doesnt get all the water all the way out of the clothes like its not spinning fast enough. Is there a way to tighten the belt ?
1 Answer Hi Donna. Check the belt for burnt spots or cracks. If it needs replaced then it is part # WH1X2026. We will need your model # to help correctly further. Make sure the pump, and hoses are not clogged. Thank you. Read More...
Greg March 16, 2012 for Model Number GJSR2080H2WW Hi. My washer won't spin. I have replaced the lid switch bought a new belt and still nothing. Sometimes it will start off slowly and spin but not often. It seems like the belt is not tight enough. The washer want's to spin. It goes through the rest of the cycles fine. Please help.
1 Answer Hello Greg. There are several possibilities in this case. First, there could be an item of clothing between the tubs. Second, the motor WH20X10063 could be shorted internally. The last thing I can think of is the spin bearing WH2X1198 could be seizing up, in which case the tub seal WH02X10383 should also be replaced. I hope this helps you solve your problem and have a great day! Read More...
Albert February 04, 2012 for Model Number GE Profile - Prodigy My Washer Drive Belt broke. I managed to remove bottom cover and take out the belt. The description on the belt is 109B4949 P006 WH1X2026 G.E.A. I'm not sure what is the part number. Can you tell me what is the part no.? I need to replace this drive belt? Thanks.
1 Answer Hello Albert! I've located part number WH1X2026, it is our part number WH1X2026. This is the exact replacement belt. Thanks! Read More...