Frank October 20, 2016 for Model Number Gld5950n10cs I just installed a new wd21x10247 main board on my dishwasher, but still doesn't respond to button pushing, but all lights are on. Did I get a bad board?
1 Answer Hello Frank. If the lights are on, then the board is fine. You will need to order and replace the control panel WD34X11287 on the unit. Read More...
Janina August 01, 2016 for Model Number GLD4560N10SS Hi When I turn the wall switch on the dishwasher starts immediately, and both "normal wash" and "heated dry" lights start to blink. I also hear the motor that also starts but nothing more happens. The panel does not respond to any touch and the only way to stop it is to turn the wall switch off. Could this be a problem with the main control board? Thank you very much for your attention! regards
1 Answer Hello Janina. Yes, it sounds like the main control board WD21X10247 will need to be replaced on the unit. Read More...
Claudio July 29, 2016 for Model Number GLD4560N10SS Hi, the dishwasher has the panel lights on, the motor spins (we can hear it) but it never starts the cycle. Could it be a problem in the main control board? Thanks for your help!
1 Answer Hello Claudio. If the motor is spinning, but it is not washing. You will need to check the impeller WD19X10038 on the unit. Read More...
Yuriy June 18, 2016 for Model Number GLD5500L00BB I use my dishwasher with option 'Heated dry',but my dishes wet. I checked heating element for continuity looks fine.What I need to do more?
1 Answer Yuriy, The most likely cause for the unit to not do the heated dry, if the heater is ok, would be either a wiring issue where a wire may be broken or a faulty main control board. Read More...
Jim March 17, 2016 for Model Number GLD4400N10WW Washer will fill with water but motor will not start for wash cycle. If I spin the motor slightly it will run and cycle thru balance of wash cycle. I can also spin motor before I hit the start button and it will cycle successfully. help
1 Answer Hello Jim. You will need to order and replace the motor WD26X10053 on the unit. Read More...
Randy October 22, 2015 for Model Number GLD5860L15S Display not working, flipped breaker to killed power to dishwasher and flipped back on after 30 seconds, dishwasher beeped when power was reapplied but same thing, display not responding when settings are pressed.
1 Answer Hello Randy. Based on the information you provided, it sounds like the main control board kit WD21X10247 will need to be replaced on the unit. Read More...
Brook October 13, 2015 Hey, my mainboard went out on my GE dishwasher and ordered the part and replaced it but all the lights came in once it was connected. I have unplugged it, I have tried to hold the reset, and tried to press the lock button for 3 sec.. Nothing has worked! What do you suggest I do?
1 Answer Brook, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Jim October 05, 2015 for Model Number GLD5960N10SS Have power to junction box but no but no lights or power to front panel controls.
1 Answer Hello Jim. Based on the information you provided, you may need to replace the main board kit WD21X10247 on the unit. Read More...
1 Answer Hello Jef. You will need to order WD21X10378 for the main board kit needed to repair the issue with the unit. Read More...
Betty August 19, 2015 One day my dishwasher wouldn't do anything no matter what buttons you pushed. That has been a month ago. Today it started to run and has ran for 4 solid hours. If I open the door it stops. If you shut the door it starts up again.
1 Answer Hello Betty. It sounds like the control panel or the control board may be bad and will need to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...