Michael April 29, 2021 for Model Number ddt595ssj2ss I have no lights on the control panel. It does not respond to any button pressing. The led on the control board is on steady. I have turned off the power several times to reset it. Still nothing. This is the third time this has happened. I was able to reset it before, but not now. I cannot get it into any diagnostic mode. What is wrong?
1 Answer Hello Michael, If power has been verified to the control, the issue is most likely the control WD21X24901C. Read More...
Mike March 21, 2021 for Model Number GDF520PGJ2BB I have no lights on control buttons. Turned power off to washer, waited and turned on still no power. I took lower cover off and dropped mother board, found small green led light continually blinking. I unpluged power from mother board and plugged back in. Now led light on mother board stays lit but still no lights on control panel and doesn't work. Is my mother board bad?
1 Answer Mike, if the LED was flashing 4 times in a second, the failure would be in the machine control WD21X24900C. If it is flashing 6 times in 3 seconds, hold the start and heated dry buttons for 5 seconds. If it is flashing 7 times in three seconds, the heating element WD05X30818 would need to be tested from the wires at the main control at connection J702. The heating element should measure 23.4O. The voltage output would also need to be tested going from the main control to the user interface and it should measure about 13VDC. If there is not voltage, the machine control has failed. If there is voltage, the user interface WD21X31899 has failed. Read More...
Joseph March 11, 2021 for Model Number ZDT915SSJ0SS Dishwasher works fine but I just lost the left half of the display light. Is this just a bulb/indicator issue that I can replace or is it the start of something big?
1 Answer Joseph, the loss of half of the LEDs would indicate that the user interface control WD21X23556 is starting to fail. Read More...
Jc March 02, 2021 My GE dishwasher control always goes out and I need to replace, why is that. What would cause that problem?
1 Answer Jc, To be able to assist properly with your question we will need to have the model number of your unit. Check for issues with loose wiring as a possibility. Read More...
Warren July 18, 2020 for Model Number GDF520PGJ2BB I have a 2017 GE dishwasher model GDF520PGJ2BB serial#GH701191B The dishwasher won't start. When I use to open the door the lights would come on and beep once and now they don't. So I shut the circuit breaker off to reset the unit and it worked for about a week. Now that doesn't work. Now if I hit the start button the lights come on. After I hit the start button to make it run after a couple of seconds the start button light starts to flash and beep and it will not run. I thought it was door latch so I replaced it. That made no difference so I replaced the main control board and still have the same issue. Any ideas what else to check?
1 Answer Warren, For this issue, you will want to check the led light on the mainboard and see what flash pattern it has in accordance with the tech sheet. If it is flashing normal standby then the issue will most likely be the display board that is faulty. Read More...
Jim April 14, 2020 for Model Number GDT695SSJ0SS Changed out the main control board on my GE dishwasher. The touch pad is still not active. The touch pad will light up when trying to check error codes, but then shuts off.
1 Answer Jim, You will want to check the wiring between the mainboard and the display board. If the wiring checks ok then this will most likely be a display board issue. Read More...
Brian August 26, 2018 for Model Number Gdf520pg2ww Hi, my machine has no power, nothing lights up and it makes no sound. I have checked power coming to it and it is good. It also appears the door switch is working probably, no continuity when the door is open, continuity when the door is closed. I’m wondering if the main control board is bad, I have it out and there are no visible burns or bad looking spots. Thanks
1 Answer Brian, Make your way to the control board and you will find a service led on the boardd.Record the number of blinks you find and they will tell you the error.Check connectorj701 pins 1 and 2 for 120 volts coming into control board.There should be a tech sheet close to the control board. Read More...
Matt A June 03, 2018 for Model Number Cdt835 My GE dishwasher stopped working. After getting a Ge technition to look at it he said the main control board was broken. I ordered the part and replaced it. Now the display does not respond. I can put it into diagnostic mode and it says active f codes none and all the lights flash. But as soon as I exit diagnostic mode the display goes blank again
1 Answer Matt, Check the door switches on the unit to make sure that they are good as this could be a potential problem. If this checks ok then double check all wiring and if the wiring is good it is possible to get a bad board. Read More...
Bill August 26, 2017 for Model Number GLD4560R10SS I replaced the tactile board and main control board on my dishwasher. The model selector resister was transferred. None of the buttons respond. The only two lights on are the "Normal Wash" and the "Heated dry". Tried resetting by turning power off. Any suggestions? Could replacement part be defective?
1 Answer Bill, If the touchpad is not working then this will most likely be caused by a faulty control panel with the control board having been replaced. Read More...
Cberr February 12, 2017 for Model Number GLD4400N10CC Lights on panel have been shutting off this week, I've reset my circuit breaker and lights come back on, but after a few minutes they shut back off. Did troubleshooting and the power to the dishwasher is hot, therefore I'm thinking it's the main control panel? Would replacing the main control panel fix the problem?
1 Answer Cberr, This issue would most likely be caused by a faulty main control board which is part number WD21X10247. Read More...