Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Refrigerator Evaporator Fan Motor Assembly by Ge

Best Seller
Manufacturer Part
4.89 (64)
By: Ge
Part Number: OEM13316436
Manufacturer Part Number: WR60X10307

Fix a warm freezer or thawing food with this evaporator fan motor. Circulates cold air over coils. DIY-friendly repair in about 30 minutes with basic tools.

More
$138.64

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Ge Refrigerator Evaporator Fan Motor Assembly (Part Number: OEM13316436)

1 Answer

David,

Test the defrost heater for continuity to make sure that it is good. If it is then the most likely cause for this will be a faulty main control board.

Read More...

1 Answer

Dan,
Without a multimeter to do some basic checks then it is just a guess as to what is actually going on and which parts to change. With the temps that you have indicated you could also have a sealed system issue.

Read More...

1 Answer

Tim,

If the fan is only running at a low speed, causing cooling issues then this would be a control board issue as it will control the speed of the motor.

Read More...

1 Answer

James, the fan can wear over time and cause a whirring noise as the shaft starts to have a wobble to it. Pressing on the evaporator cover can provide enough of a pressure to quiet the noise but you will want to check the fan motor to ensure that it the issue. It may be possible that a fastener came slightly loose and can cause this as well.

Read More...

1 Answer

Doug,

You would need to remove the upper panel to be able to replace the evaporator fan motor on this unit.

Read More...

1 Answer

Hello John. This motor is a OEM GE part but we are not sure who manufactured it. Thank you.

Read More...

1 Answer

James,

Yes the evaporator fan motor not running would cause the freezer and fresh food to not be cold enough and will cause the icemaker to not make ice.

Read More...

1 Answer

Hello John. You will need to test for power coming to the fan motor. If it is there, then you will need to replace your fan motor. If it is not there, you will need to replace the main board.

Read More...
Rodo for Model Number PSS26MSTASS

The freezer gets warm sometimes (every few months). The temperature reader goes up to about 10F or 11F (normal is 0F). There was frost inside the freezer (rear). The next day the freezer is at 0F and there are some frozen droplets inside (rear) the freezer. The fridge is fine. I tested the voltage at J2-3 and J2-4 for the evaporator motor (after leaving the freezer door open for 3 minutes). The voltage was zero until the compressor kicked on. Then it showed 2v, then after a few seconds it show 6v until it got to 12v or so. Will this be an evaporator motor or main board problem? Thanks

1 Answer

Rodo,

Based on the voltage reading that you are getting it sounds like the motor and control are communicating and have the proper voltage. With frost being on the rear wall would sound more likely to be a defrost issue. You can check the defrost limiter to see if it has continuity. If it does not have continuity then you would not need to change it out. You will also want to check the defrost thermistor for resistance. The resistance values should be as follows, 42.5K at 0 degrees, 14.4k at 37 degrees and 5K ohms at 77 degrees. If not within range then it would need to be replaced. If it checks good then also check the defrost heater for continuity. If no continuity then replace and if good with continuity and all other components check ok then you would need a new main control board. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Read More...

1 Answer

Hello Catherine,
This sensor is necessary for the proper temperature to be maintained in the unit. This could also set a fault code in the control since it will be looking for the signal from this sensor.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google