Monica March 24, 2014 for Model Number WM2050CW I am having trouble with my machine not draining and an OE error message. I have pulled the screen out of the pump and cleaned and made sure nothing was kinking the hose. Could this be I need a new drain pump?
1 Answer Hello Monica. If there is power coming to the drain pump, and it is not draining, you will need to order and replace the drain pump 4681EA2001T on the unit. Read More...
Bryan March 14, 2014 for Model Number WM2077CW I have part 4681EA2001D, can I use this or do I need 4681EA2001T?
1 Answer Bryan, Both of the pumps are the same and you can use either part number. The APP part number for both pumps is 4681EA2001T. Read More...
Yasmin March 10, 2014 for Model Number lg wm3431hw I would like to install the drain pump but the washer on your your video is for a different than my washer. Please help.
1 Answer Hello Yasmin, This pump 4681EA2001T is the correct one for your unit. The video is only to give a general idea of how the job is accomplished and is not exact since there are thousands of model configurations out there. Read More...
Tracy M March 02, 2014 for Model Number LG WM2233HW On this LG model washer do I use the 4681EA1007G pump? From what I've read if my washer won't drain, the pump is bad. The other issue I have is it will not spin; but I am wondering if that has to do with the water level in the tub preventing it from going ino spin mode? Also, I notice you have the video for the Kenmore, but how do I get to the pump on the LG?
1 Answer Tracy, Yes the correct pump for your unit would be part number 4681EA2001T. You will want to make sure that the drain pump is not clogged or have obstructions in it and also check to make sure that there is power to the drain pump when the unit is calling for the pump to come on. If there is power and the pump is clear then the pump would need to be replaced. The unit will not spin properly if it is not draining the water out. Read More...
Mark February 27, 2014 for Model Number wm2301hw What is the part # for a drain pump for a lg wm2301 washer?
Dan F February 27, 2014 for Model Number LG WM2487HWMA STEAM WASHER I Just Changed My Drain Pump(using Your Video Which Was Very Good) Because Water Was Not Being Drained From Washtub And Was Getting Oe Error. After I Finished Putting Back Together I Ran Washer And To My Chagrin, Tub Drain Completely But Drain Pump Kept Running And Got The Oe Error Again. Inside Wash Tub Empty Of Water, But Drain Pump Kept Running And Would Not Go Into Rinse Cycle… Any Ideas Would Be Much Appreciated. Another Question Is The Drain Pump Housing That Is Connected To Drain Pump, Is There Suppose To Be Any Mechanical items In The Housing, I Pulled Out What Look Like Underwire From Bras Out Of The Housing, I'M Hoping I didn't Pull Out Anything Of Importance Out Of Housing. Just Wanted To Make Sure Housing Was Just Open Plastic To Connect Drain And recirculate Pump To.
1 Answer Hello Dan. You need to check the pressure switch on the unit and the pressure hose on the unit. Either if bad could cause the issue. Read More...
Jeff February 27, 2014 for Model Number WM2455HW Was having a problem with this washer draining. Checked the pump and the ohms showed more than what it should have been. Now the machine drains but still comes up OE. All hoses are clear. The new pump shows 15.4 ohms and I am getting 120 VAC to the pump. What could be the problem?
1 Answer Hello Jeff, You need to remove the hose that runs from the outer tub to the pump and make sure an item, (such as a sock), is not between the tubs and blocking the drain opening. Also check the other hoses for blockages. If there is no blockage and the unit is fully draining, replace the main board EBR32268002 since it is misreading the information to being sent to it. Read More...
Rich D February 18, 2014 for Model Number LG WM2010HW I have been having problems with having to constantly drain the tube below every week after washing maybe 5 loads max otherwise washer will leak below and water will fill in the soap dispenser above. Is this normal for this washer or could the pump below be clogged or partially working. I took the top off and see no wetness around the intake valve or black bellows hose. I have had the large rubber seal around the door replaced recently which did have a tear. I checked the new one and do not see a tear.
1 Answer Hello Rich. Either the pump filter is clogged or the drain pump is bad and will need to be replaced on the unit. Read More...
Leticia C February 17, 2014 for Model Number WM2487H*MA Do you carry the drain pump for this model? If not where do you think I should look for it?
Rachel T February 14, 2014 for Model Number WM3988HWA We replaced the drain pump about a year ago and it worked fine, but now it's not draining again. It's not making the noise it did before. Checked for blockage and no error messages. Is there something else that would need to be replaced? Does it need the drain pump replaced again, if so, why would it only last a year?
1 Answer Hello Rachel. If there is power to the pump, and it does not drain, you will need to replace the pump on the unit. As for only lasting 1 year, we have no way of determining what could cause that issue. Read More...