Jon August 12, 2011 for Model Number lg wm1814cw Do I really need to mess with the top and the door or can I just tip the machine back and get right at the pump without ruining my washer? It is easily accessable.
1 Answer Hello Jon. The instructions provided are from the manufacture for replacing the pump 4681EA2001T. If you can access the pump from under the machine and do a proper repair, then it should be fine. Which ever way is easier for you. Hope this helps. Read More...
Percy July 28, 2011 for Model Number WM1814CW I AM HAVING PROBLEMS LOCATING/FINDING THE PART NUMBER TO THE O-RING (SIZE 3")THAT IS LOCATED INSIDE THE DRAIN PUMP. THE PART NUMBER TO THE DRAIN PUMP MOTOR IS AP444072. ALSO, AFTER REMOVING THE DRAIN PUMP MOTOR-I NOTICED THAT WATER HAS GONE INSIDE THE PUMP, DUE TO THE O-RING IS LOSE. CAN THE DRAIN PUMP BE REUSED WHEN IT IS DRY & THE O-RING REPLACED? NEED ANSWER ASAP - THANK YOU
1 Answer Hi Percy. Yes, most of the time when the pump is dry completely you can reuse the pump. In searching L.G. parts breakdown, i cannot find the o-ring requested. The o-ring is only sold with the pump itself. Hint's: You can either momentarily reuse the o-ring by putting some petroleum jelly on it and it will seal for some time. You can go to Ace Hardware and match up the o-ring to either American size or metric size. The pump part # is 4681EA2001T. Hope this helps. Thank you. Read More...
Steve July 25, 2011 for Model Number wm3677hw It makes a growling sound and will not drain the water . From the back of the machine I can see the pump in the front right corner. How do I get to it so I can change?
1 Answer Hello Steve. Here are the instructions from the manufacture for the pump 4681EA2001T. Hope this helps. Disassemble the cabinet cover. Unscrew the 4 screws from upper of the canbinet cover. Unscrew the screw from filter cover. Put a flat ( - ) screwdriver or putty knife into the both sides of the filter cover, and pull it out. Unscrew the screw from the lower side of the cabinet cover. Open the door. Disassemble the clamp assembly. Tilt the cabinet cover. Disconnect the door switch connector. Lift and separate the cabinet cover. Separate the pump hose, the bellows and the circulation hose assembly from the pump assembly. Disassemble the pump assembly in arrow direction. Read More...
Jan July 22, 2011 for Model Number LG washer WM2077CW My water wont drain out was making alot of noise like bearings were going out. Is this just the water pump or should I look for other issues? Would make cycle until the draining part the would give a OE code on display screen. Water was still in the tub. Please Help husband travels and I have to fix this myself. Also if you have a diagram of where this part is located would really appreciate this. Also include part number so I can order asap. Thanks Jan
1 Answer Hello Jan. Remove the front pump cover and remove the filter from the pump housing. See if the filter is clogged. If it is clear, you will need to replace the pump motor 4681EA2001T. Unscrew 2 screws on the back of the top plate. Pull the top plate backward and upward. Disconnect the Display PWB Assembly connector from Trans cable. Pull out the drawer and unscrew 2 screws. Lift the left side of the Control Panel Assembly and pull it out. Unscrew the 4 screws from upper of the canbinet cover. Unscrew the screw from filter cover. Put a flat ( - ) screwdriver or putty knife into the both sides of the filter cover, and pull it out. Unscrew the screw from the lower side of the cabinet cover. Open the door. Disassemble the clamp assembly. Tilt the cabinet cover. Disconnect the door switch connector. Lift and separate the cabinet cover. Separate the pump hose, the bellows and the circulation hose assembly from the pump assembly. Disassemble the pump assembly in arrow direction. Hope this helps. Read More...
Kristen July 19, 2011 for Model Number WM2277HS I need help finding a drain pump for my lg washing machine modle number wm2277hs. It is saying a code OE and they say there is something blocking the filter or pump but I have cleaned everything out and it will go thru the whole cycle until it gets to the rinse cycle and it wont drain out the water. Can you help me?
1 Answer Hello Kristen. Based on the model number you provided, 4681EA2001T is the correct drain pump assembly. Hope this helps. Read More...
Calvin July 17, 2011 for Model Number WM1812CW Where is the location of overload protector located for motor?
1 Answer Hi Calvin. The pump motors are an" isolated " 120vac non grounded unit. The pumps of this type are synchronous motors without overloads. Is the outlet flapper OK? Is the impeller loose on the pump shaft spinning and giving a low volume output? Thank you. Read More...
Matt June 15, 2011 for Model Number wm1814cw On drain mode only it makes a clicking noise thinking the blades on pump might be bad.
1 Answer Hello Matt. Check and make sure nothing is stuck inside the pump assembly. If it is clear, you will need to replace the pump motor 4681EA2001T. Hope this helps. Read More...
Robert April 29, 2011 for Model Number Wm1832 cw Pump has died and can't find the pump for our model. Please help!
1 Answer Hello Robert. Here is the part number for your pump motor 4681EA2001T. Hope this helps. Read More...
Mark April 24, 2011 for Model Number WD-3274RHD Drain pump died. Can it be reached from side or bottom, or does whole cabinet have to come apart? How long to get the part? Thanks
1 Answer Hello Mark. The best way to access the pump is to remove the front panel of the machine. You will need to remove the top panel and the control panel. Then remove the spring around the door boot, and the screws holding the front panel on the washer. Then you will be able to access the pump assembly. The part will ship between 10-14 business days after the order is placed. Hope this helps. Read More...
Rj April 23, 2011 for Model Number mw11814cw My washer quit sucking out the water. I have taken the washer apart and there are no blockages. Do you think the pump is bad? And if so which part number do I need? K340?
1 Answer Hello RJ. Check and make sure you have power coming to the pump. If so, and the pump does not run, you will need to replace the pump assembly. 4681EA2001T is the correct pump motor for your model. You can test this with a multi-meter MA-DM1. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...