Maria February 03, 2023 for Model Number WF395BTPA The machine fills with water and when it begins the washing process it gives me a dE error. Does this mean I have to replace the door mechanism?
1 Answer Maria, That is correct, the code is a door lock error code and it is likely the lock needs replaced. Read More...
Julie Schmeckenbecher March 01, 2022 for Model Number WF56H9100AG/A2-0000 gives a ue error code has been reset
1 Answer Julie, The UE error code would be an unbalanced load which would cause the no spin issue. You will want to check to make sure that the clothes are not off-balance. If the clothes are fine then this will either be faulty shocks, broken spider or possibly bearings that are bad. Read More...
Kh February 19, 2022 for Model Number WF42H5000AW/A2 What part do I need to replace the door lock assembly on my front loading Samsung VRT washer?
Irma October 26, 2021 for Model Number WF42H5200AP/A2-0000 Is this part compatible replacement DC34-00024B.?
1 Answer Hello Irma, the manufacturer lists door lock assembly as part DC64-00519B DC64-00519B, for your model, there is no substitute part listed. Read More...
Guillermo November 30, 2020 for Model Number wf45h6300ag/a2 The front door is not locking, we check and we replaced the switch PN dc64-00519b because that is the number provided by sears specialist service with the model we provided. We changed and it is not working, its keeps looked and the door is not open, then I took the old switch and find out the manufacturer emz PN 461970200692, looked on the internet and found the PN dc34-00024b, I come back with the service people and they told me that the part number DC34 its a part number, however, the DC54 is an upgrade part number and we should be able to use. I need to understand which pn to use based on my model and confirm that is working. Please if you can help I will highly appreciate it.
1 Answer Guillermo, the door switch needed is going to be dependent on the REV number of your model. If the REV is 00, then the door switch DC64-00519B would be used. If the REV number is 01, the door switch DC64-00519D would be used. Read More...
Jerome November 23, 2020 for Model Number WF56H9100AG/A2-0000 my washer gives me a 4E code Can you tell me what may be the problem
1 Answer Jerome, The 4E error code indicates that there is a water supply error. You will want to check to make sure that the screens on the water valve are not clogged. Make sure that there is adequate water pressure to the valve. If there is nothing wrong with the supply or with the valve screens being clogged then you will want to test to make sure that you are getting 120 vac to the water valve when it is supposed to fill with water. If there is proper voltage then the valve would need to be replaced. If there is not proper voltage then the main control board will need to be replaced. Read More...
Frank April 04, 2020 for Model Number WF405ATPAWR/A2 My Samsung washer was getting the FL code. I replaced the door latch mechanism. Did not help. Then I purchased a new control board. The washer started and door locked. It got through most of the wash and then got an nd error code. After turning back off and back on, the washer is back to getting the FL error... clicking a few times and not locking door. Wondering if this is caused by a faulty component connected to the board??
1 Answer Frank, it would be recommended that the wiring DC93-00251K from the main control DC92-01063A to the lock assembly DC34-00024B are inspected for any loose connections. It is also recommended that the wiring is inspected for any signs of pinched wires or bare spots. The wires will also need to be tested for continuity to identify if there are any breaks in the wires. The door will also need to be inspected to identify if the door is shutting fully and allowing the strike to activate the switches in the door lock. If all of this check good, the door lock will need to be tested for resistance from terminal 3 to terminal 5 and should read 949O. If the door lock is not measuring 949O, it would need to be replaced. If it tests good, and the wires tested properly, then the main control would be the cause of this issue. Read More...
Frank March 23, 2020 for Model Number WF448AAW/XAA 02 Which door lock assembly do I need for this washer as the part number that is on mine does not come up on your site
Sheryl January 18, 2020 for Model Number WF350ANW/XAA-04 On my front load washer the receptacle for door latch is broken. Door will not latch and swings open. How can I fix it? How to I get appropriate part?
Vlad August 21, 2019 for Model Number samsung wf45k6200aw/a2 Samsung washer starts clicking, but then stops, no water flowing in. At some point showed code dc, then dc3. Samsung customer service said it's the door lock, referred me to J & J International, Inc. J & J refused to give me a correct part number, just quoted a price. Their website shows 2 parts: DC64-00519D and DC34-0025D, the first one mentions solenoid. Amazon prices vary greatly. Which one is the correct part for Samsung WF45K6200AW/A2 washer?
1 Answer Vlad, The correct part number for the model number you supplied is DC64-00519D / DC64-00519D Washer door lock switch. The part is in stock and available at this time. Thanks, Read More...