Kc November 10, 2023 for Model Number MFI2568AEW The ice tray for Maytag refrigerator MODEL # MFI2568AEW wont lock into place, therefore ice only comes out through the door dispencer for a short time, only a few cubes of ice come out. Then the ice tray backs out of place and ice stops coming out through the door dispencer. The auger turns & ice maker makes ice, the tray just wont lock into place. Ive checked and nothing/no ice is blocking the tray from locking into place. The ice tray does not appear damaged. Can you advise what is broken and what needs replaced, Thank you.
1 Answer KC, if the lock strike on the ice section is not damaged and there are no obstructions, the most likely cause of failure would be the locking mechanism in the ice container WPW10324090 has failed. Read More...
Gerry March 26, 2021 for Model Number AFI2538AEB The ice maker bucket keeps coming off from where it belongs. I have to push it back in and it latches for a while and then comes off again When its off no ice comes out thanks Gerry
1 Answer Gerry, Check to make sure that the auger inside the ice bin is not binding up as this could cause the ice bucket to slip out. If it is binding and there is nothing causing the bind then this will require a new ice bin. Read More...
Tina November 18, 2020 for Model Number MFI2569YEMO I need help figuring out what is wrong with my icemaker so I can buy the right part. One day the water just started pouring out and wouldn't stop. It was like a ghost was filling up an invisible glass of water. I opened the door and water was pouring out of the icemaker which had filled with water. The other day, there was water on the floor (it must have happened again but I didn't see it this time) Can you tell me what is wrong with it? The refrigerator is 9 years old. Thank you, Tina
1 Answer Tina, it would be recommended that the water valve WPW10312696 is tested for 120 Volts AC. If there is not 120 Volts going to the valve, the valve has failed and would need to be replaced. If there is 120 Volts AC, the ice maker WPW10300024 has failed and would need to be replaced. Read More...
Dave May 04, 2018 for Model Number Gi5svaxvl00 I just received my replacement bin and it does fit perfectly. My question is the ice flap door on the bin now has a noticeable gap on it. It looks like by design. My old bin the flap door has no gap . This gap will allow cold air to seap into the frig space and I already have issue with it being too cold. I could send pics.
1 Answer Dave, The ice bin that would work for your unit would be WPW10324091 which looks like you may have gotten the wrong bin. Read More...
Eric July 03, 2017 for Model Number MFI2569VEM2 The yoke connected to my ice tray door seems to have gotten spun around the 180 degrees somehow and now the ice tray won't go back in?
1 Answer Eric, If the bin is damaged where it will not go back in then you would need a new ice bin for the unit. Read More...
Greg July 23, 2016 for Model Number MFI2568AEB We need just the spring that's attached to the yoke extending from the ice bin. This spring is shown on the far right in your image #1 of the ice bin p/n AP6019564. Any chance we can purchase just this spring, or a couple of them? Thanks, Greg
1 Answer Greg, Unfortunately the spring is not available as a separate part and would need to get the entire bin for this part. Read More...
Mary March 28, 2016 for Model Number MFI2568AES Maytag Ice 2 0 French Door Bottom Freezer I need the ice bin /auger part for this model as the bin wasn't always inserted correctly and end pieces of auger are worn away. I have seen the picture of the part I need but it doesn't show a side button that I need to push to open the bin drawer. I want to order the correct part for my freezer. Do you have the one I need?
1 Answer Hello Mary, The manufacturer lists WPW10324090 as the correct ice bin for the model provided. The third picture of the part on our site shows the release button on the side. Read More...
Bill January 05, 2016 for Model Number MF12568AES My ice maker for some reason started making 2 to 5 cubes stuck together which broke the blades and I am wondering before buying a new bin assembly, how can I stop it from over pouring water in the ice tray?
1 Answer Hello Bill. If the icemaker is over filling, you will need to replace the water valve 67006322 along with the icemaker in the unit. Read More...
Sharon June 27, 2015 for Model Number MFI2568AEW When I push the button in on the ice bin cover I cannot get the bin to slide out. Can't get any ice so I am assuming there is an ice jam somewhere. The auger doesn't move either. when I try and get ice i just hear a humming sound. Your help is much appreciated. Thank you
1 Answer Sharon, If there is a ice jam then you will basically want to push the button and grab the opening at the bottom of the bin and pull as hard a you can. This will be the only way to get the bin out. Read More...
Keith August 25, 2014 for Model Number MFI2568AES Ice maker auger gets jammed and does not turn to empty ice. Most times the auger screw end cap dis engages from the bucket. What to do and buy
1 Answer Keith, The auger disengaging would be caused by a bad bin and the entire ice bin would need to be replaced. The individual parts are not available. The bin is part number WPW10324090. Read More...