Jim September 22, 2018 for Model Number WDT910SSYW0 Is there a way to get only the impeller since the rest of the pump is still working? The impeller in mine has come off the shaft and and now is to loose to continue spinning at such speeds.
1 Answer Jim, Unfortunately the impeller only comes with the pump motor and not available separately. Read More...
Colin April 18, 2018 for Model Number WDT920SADH0 Does pump W11032770 only run if it is supplied with 120V AC? My pump drains with 120V AC applied, but does not wash. The voltage is only around 14V AC for washing. I assume this is not correct and I have a bad control board?
1 Answer Colin, This pump motor with 120 vac applied should run but if it is only getting 14 vac then the issue will be with the control board. Read More...
Keith January 08, 2018 for Model Number 66513402n410 The kenmore dishwasher is not draining. I checked the drain line and it is clear. I replaced the drain motor and still not draining. I hear it washing, but at the pauses it does not drain. When I stop it mid cycle, and push the cancel wash button, the water does not drain.
1 Answer Hello Keith. Check the wiring to the pump and also make sure the pump is getting power. If not, and the wiring is good, then the board is bad and will need to be replaced. Thank you. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Chuck November 19, 2017 for Model Number KDTE104DSS0 There is no water coming through the spray arms. There is no blockage. I replaced the diverter motor and still no water circulation in the spay arms. Could the problem be the pump?
1 Answer Chuck, Check to see if there is power getting to the pump. If there is power to the pump but not running then the issue will be a faulty pump assembly. Read More...
Howard June 18, 2017 for Model Number WDF780SLYB2 If I hook up 110Vac to the Motor Pump, W10510667 , and nothing happens, would this confirm the pump is bad?
1 Answer Hello Howard, This is a 120Vac, 60Hz motor, so yes, if voltage applied does not make the motor operate, it is bad. Read More...
Howard G June 17, 2017 for Model Number WDF780SLYB0 I'm pretty sure the pump is bad. Is there any way to take the pump apart and check the impeller? If not, is there a way to check it without ordering a new one? I have changed the door lock, inlet valve. I have watched the dishwasher running and when it is supposed to be washing the dishes, I can see the water leave the bottom and a little water comes out of the blades but they do not spin. I have cleaned all the blades and still have the same problem. Thanks for your help.
1 Answer Howard, The only way to check the impeller would be to look inside the pump to see if there is any damage to it. This issue does sound like the pump would be the issue. Read More...
Wanda April 20, 2017 for Model Number 665.13259k112 Does it take any special tool to install the pump/motor assembly #WPW10510667? Crimping the 'button' clamps?
1 Answer Hello Wanda. No, you can simply squeeze the clamps with a pair of pliers to crimp them. Thanks. Read More...
Edson L March 19, 2017 for Model Number WDT720PADM0 Dishwasher not cleaning. Washer rotos not running. I hear a "transformer type noise " when washer show run. I removed the washer pump motor and measured 5 M ohms . Does it justify the issue / noise ? Why this motor / pump W11032770 comes with the rubber ducts ? I could not remove them from the dishwasher . Motor + rotor was removed easily. Regards Edson
1 Answer Edson, With the spray arms not spinning then this issue sounds like it may be caused by a faulty diverter motor which would be part number W10537869. This diverter motor will allow water to be moved from upper to lower spray arms and it being defective will cause the spray arms to be inoperative. Read More...
Joel December 30, 2016 I Just need the 2 button head clamps for the 90° hose on the pump. Do I have to buy a whole pump assembly for that?
1 Answer Hello Joel, If these clamps are available they will be on the parts list for your model. I'm sorry but we are unable to look this up for you without the model number from your units' I.D. tag. Thank you for your patience and understanding in this matter. Read More...
Reagib July 29, 2016 for Model Number 665.13699N410 Hi. Kenmore dishwasher just over a year old. It fills with water, and drains just fine, but the water does not circulate. For awhile, it would work about every other time, now, it does not work at all. Would it be the pump motor? How could I test it? Thank you!
1 Answer Hello Reagib. You will need to test for power to the pump motor on the unit. If it is there and the pump does not run, you will need to replace the pump. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...