Tim August 31, 2013 for Model Number Whirlpool SlimTwin LTE5243DQ3 Washer fills with water OK, goes through wash cycle and then stops at the end of the cycle. Will not pump down, rinse or spin in any of the different Wash modes. I hear the timer making noise in the rinse mode.
1 Answer Hello Tim. Check and see if the lid switch is bad and will need to be replaced on the unit. Read More...
Tim August 31, 2013 for Model Number Whirlpool ThinTwin LTE5243DQ3 During a wash cycle the washer stopped working with a full tub of water. Moving the dial to different settings it would occasionally turn on in the rinse cycle but not in wash or spin. It would not pump the water from the tub. Now nothing happens except in the rinse cycle I here buzzing from the water valve solenoids. Is it possible that a faulty water valve solenoid can shut the washer down?
1 Answer Hello Tim. Yes, if it is not letting in the water, it will shut down the washer. Read More...
J Williams August 29, 2013 for Model Number wjsr416odocc The cold water will not come in following a power surge, only the hot comes in now.
1 Answer J. Williams You will want to check to see if the valve is getting power. If there is power to the water valve then the valve is faulty and would need to be replaced. If there is no power then the control would be faulty. Read More...
Rosetta August 29, 2013 for Model Number Wm2487hrm My LG top load washing machine is not working the water does not go in the machine. Does not start. What is the problem.
1 Answer Hello Rosetta, If the power cord is plugged in and the water is turned on to the unit, the water valve, pressure switch, or a clogged pressure switch hose can cause this issue. These are issues with a top load machine. The model number you provided is a front load machine. Since the parts for the two are not interchangeable, you may want to verify the model number off of the units' I.D. tag and get back with us. Read More...
Jerry M August 16, 2013 for Model Number 110.82984800 The water will fill about 2" and stop. I turn the water level back and forward and it may fill 2 more 2". I can move the time to spin and get the water out. Is this the water level switch on the panel gone bad?
1 Answer Hello Jerry. Blow through the pressure hose and make sure it is not clogged. If clear, replace the pressure switch on the unit. Read More...
Joe L August 07, 2013 I have a washer that the water will not shut off at any set level it will continue and overflow out of the washer. Could this be a water into value problem?
1 Answer Hello Joe. If you can stop the water from entering the machine by turning off the timer or unplugging the unit, you will need to look for a bad pressure hose or replace the pressure switch. If the only way to shut off the water is at the shut off for the water hoses, you will need to replace the water valve in the unit. Read More...
Sophia August 04, 2013 for Model Number lsr5232lq1 Washer fils with water but will not spin to let the water out. What is wrong? What part do I need? Someone told me I need a new water valve. Is that correct?
1 Answer Hello Sophia, If the unit is filling with water, the water valve is fine. You should check the pump WP3363394 for debris and the motor coupler 285753A for wear and damage. Read More...
Nam August 03, 2013 for Model Number kenmore I have a kenmore washer heavy duty 70 series, and model number is 110.92274100, looking for a inlet valve. I checked and found a part in your site. Only difference is color. The one I have is Red color and the valve in your site is blue. My question is "the valve in your site is compatible with one I have?"
1 Answer Hello Vincent, If the drain time exceeds eight minutes, "F21" will be displayed, the water valves will turn off and the pump will stop running. Press PAUSE/CANCEL to drain the machine. The display will be cleared and the machine will turn off after a maximum of eight minutes. Possible Causes/Procedure 1. Check the drain hose and make sure it is not plugged or kinked. 2. Unplug washer or disconnect power. 3. Check the electrical connections at the pump and make sure the pump is running. 4. Check the drain pump filter for foreign objects. 5. Plug in washer or reconnect power. 6. If the above does not correct the problem, go to step 7. 7. Unplug washer or disconnect power. 8. Replace the pump. 280187 Read More...
Sam F June 24, 2013 We have a whirlpool washer machine mod#LSR8233EZO. When the cycle is finished it contiunes to drip water in the tub. Think it may be the fill valve but can not find one that matches our model #. Can you help? Thank you.