Parts for Frigidaire LRA257ST211: 03 - Recommended Spare Parts

This refrigerator water filter removes common impurities from the ice and water supply so you get cleaner-tasting water and clearer ice. Designed to fit inline/replaceable filter housings used in many Frigidaire refrigerators. What it does:

• Reduces chlorine taste and odor for improved drinking water flavor
• Helps reduce sediment and particulates that can affect ice clarity
• Keeps water flowing properly when replaced as part of routine maintenance
• Addresses symptoms like cloudy ice, bad-tasting water, or reduced water quality

• One replacement refrigerator water filter cartridge

• Replace filter according to your refrigerator manufacturer's instructions; typically twist or push in to seat and lock
• Run several gallons of water through the dispenser after installation to flush the system and remove loose carbon fines
• If water flow is restricted after installation, check filter orientation and seating; do not force
• For safety, disconnect power to the appliance before accessing internal filter housings

This frame is the exact replacement trim piece that restores the appliance's front appearance and supports adjacent panels. Replacing a damaged or bent frame improves fit and helps keep internal parts protected from debris. What it does:

• Provides structural support and alignment for the appliance front panels
• Covers and protects edges where panels meet to prevent dirt and moisture intrusion
• Restores cosmetic appearance if the original frame is scratched, dented, or warped
• Helps maintain proper door or control-panel fit when worn or bent

• One replacement frame

• Disconnect power to the appliance before starting any repair
• Installation typically requires removing adjoining trim or screws; retain fasteners for reuse
• Use hand tools and avoid over-tightening to prevent cracking the new frame

Color: gray. Measures about 2 inches wide by 3-1/2 inches deep.

This capacitor helps start and run the refrigerator's compressor and/or fan motors so the appliance cools reliably. Replaces a worn or failed capacitor to restore normal motor operation and reduce hard-starting. What it does:

• Provides the initial electrical boost motors need to start turning
• Helps maintain steady motor speed during operation
• Commonly linked to symptoms like compressors that hum but don't start
• Needed if refrigerator cycles frequently or cooling is inconsistent

• One capacitor

• Disconnect power before accessing electrical components
• Discharge the capacitor before touching terminals to avoid shock
• Verify wiring and terminal orientation before reconnecting

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

This electronic control board is the appliance's main PCB that manages functions and the user interface. Replacing a failed board can restore normal operation when the unit is unresponsive, erratic, or displaying control-related errors.

• Directs operation of key components based on user settings and sensor feedback
• Powers and communicates with the display/interface and control pads
• Coordinates timing through relays and interfaces with safety/protection circuits
• Common symptoms: no response to buttons, dead/blank display, unexpected cycling or beeping, control error codes, or visible damage on the old board

• Disconnect power before servicing and verify no voltage is present
• Use ESD precautions; handle the PCB by the edges and avoid flexing it
• Photograph/label connectors; transfer each to the same location on the new board, matching any jumpers or DIP-switch settings if present
• After installation, restore power and run the model's test/diagnostic or a cycle to confirm proper operation

This blower wheel moves air through the dryer cabinet so clothes dry efficiently and the appliance vents properly. Replacing a worn or damaged wheel restores airflow and helps prevent overheating and long dry times. What it does:

• Spins on the blower motor shaft to draw air across the heating element and through the drum
• Restores proper airflow when a chipped or bent wheel causes reduced drying performance
• Reduces rattling or vibration caused by imbalanced or cracked fins
• Helps prevent overheating and extended cycle times due to restricted airflow

• One blower wheel

• Disconnect power (and gas if applicable) before servicing to avoid electric shock or injury
• May require removal of the dryer front or blower housing and loosening the motor to slide the wheel onto the shaft
• Ensure the wheel is oriented and seated correctly on the motor shaft and that set screws or clips are tightened as required
• Inspect motor shaft and housing for debris; spin the new wheel by hand to ensure free rotation before reassembly

This replacement blade fan moves cold air across the evaporator to help maintain even temperatures inside the compartment. It restores proper airflow for more consistent cooling and helps reduce frost buildup when working with a good motor. What it does:

• Circulates air across the evaporator to distribute cold air through the compartment
• Restores airflow when a cracked, warped, or missing blade reduces cooling efficiency
• Helps reduce uneven temperatures and localized warm spots caused by poor airflow
• Can reduce abnormal noises caused by damaged or unbalanced blades

• One replacement blade fan

• Disconnect power to the appliance before starting any repair
• Remove the evaporator cover/panel to access the fan assembly per your model's service instructions
• Handle the replacement blade carefully to avoid bending the blades or contaminating the evaporator
• If the fan motor or mounting hardware is damaged, replace those parts as well for reliable operation

This replacement cover is an access panel that protects internal components and keeps the appliance exterior finished. It restores a clean appearance and helps prevent dust, debris, and accidental contact with internal parts. What it does:

• Covers and protects internal appliance components behind the cabinet or control area
• Maintains a finished exterior and prevents small objects from entering service areas
• Helps reduce dust buildup on internal parts that can affect performance over time
• Commonly replaced when scratched, cracked, or damaged during service or impact

• One cover

• Disconnect power (and water/gas if applicable) before starting any repair
• Handle edges carefully; use appropriate fasteners and follow OEM placement for a flush fit
• If mounting hardware is damaged or missing, replace with OEM-specified screws for secure installation

This cabinet is the refrigerator's main outer housing that provides the finished exterior and structural support for internal components. Replacing a damaged cabinet restores the appliance's appearance and helps protect internal parts from damage. What it does:

• Forms the appliance's exterior shell and supports internal assemblies
• Protects internal components from dust, moisture and accidental impact
• Restores a dented, cracked or cosmetically damaged exterior
• Helps reduce rattling by providing a secure mounting surface

• Disconnect power and empty the appliance before starting
• Cabinet is large and may be heavy—use a helper to avoid injury or damage
• Expect to remove trim, doors and mounting hardware to access cabinet fasteners
• Keep screws, clips and seals organized for reassembly; replace damaged fasteners or seals as needed