Maytag Washer A312S Leaking

The Injector Valve is an OEM replacement part specific to Whirlpool washing machines. It plays an important role in properly dispensing detergent into the wash load. Located inside the detergent dispenser drawer, the injector valve regulates the flow of water at timed intervals to fully dissolve and evenly distribute detergent among clothes. Washer air gap rubber injector. For the injector nozzle order WP213015. For a kit that includes the injector valve, nozzle, and two clamps order 12001677

Causes of a bad injector valve can include clogging from mineral deposits or debris, wear and tear from regular use, or damage from high water pressure. A malfunctioning injector valve can lead to improper water levels and affect the washing machine's performance.

Symptoms of a bad injector valve include:

• Inadequate water filling the washer
• Water leaks around the valve area
• Unusual noises during the water filling cycle
• The washer not advancing through cycles properly
• Visible debris or deposits at the injector valve opening

It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washers.

The Mounting Stem Repair Kit is an OEM part for Whirlpool washing machines. It includes all necessary components to repair the mounting stem, which is a critical part of the washer's tub support system. Comes with the hub assembly, seal, and spanner nut. 6-2040130 should also be replaced at the same time. A spanner wrench is required to complete the repair TB123B.

Symptoms of a bad mounting stem include:

• Excessive noise or vibration during the spin cycle.
• The washer tub appearing loose or off-balance.
• Leakage around the central area of the washer, indicating a possible seal failure.

Causes of a bad mounting stem can include wear and tear from normal usage, especially with heavy loads, or corrosion and material fatigue that weaken the stem's integrity.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This injector nozzle channels incoming water from the fill hose into the wash basket. Replacing a cracked or clogged nozzle helps stop leaks and restores a clean, controlled water stream during fill. What it does:

• Directs incoming water into the tub via the injector assembly
• Works with the injector cap to diffuse flow and reduce splashback/siphoning
• Maintains a proper spray pattern during fill
• Common symptoms include water leaking or spraying from the injector area, visible cracks, or mineral buildup restricting flow

• 1 injector nozzle

• Disconnect power and turn off water supply before servicing
• Access the injector assembly by removing the cabinet/top per your model's procedure
• Release the hose clamp, remove the old nozzle, and install the new nozzle oriented toward the tub; reinstall the injector cap if your model uses one, and secure the clamp
• Restore water and power, then run a test fill to check for leaks

The Injector Hose Kit is an OEM part for Whirlpool washing machines. This kit includes the hose necessary for injecting water into the washing machine tub during the wash cycle. It ensures that water is properly directed into the tub for effective washing.

Common causes of a bad injector hose kit include wear and tear from regular use, cracks or splits due to age, or damage from accidental mishandling.

Symptoms of a bad injector hose kit include:

• Water leaks from the hose
• Insufficient water entering the tub
• Poor washing performance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Siphon Break is an OEM part for Whirlpool washing machines. It is a critical safety component that prevents the backflow of contaminated water from the washer into the fresh water supply line. For the gasket use part number [AP6005834], For the siphon elbow use part number [AP4024083]

Causes of a faulty siphon break include physical damage, clogging due to mineral buildup or debris, or general wear and tear over time.

Symptoms of a bad siphon break:

• Water leaks or puddles around the washing machine
• The washer not filling with water properly
• Potential for contaminated water to enter the fresh water supply

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

The Sleeve is an OEM replacement part for Whirlpool top-loading washing machines. As an internal part, this sleeve surrounds a shaft connecting the drive motor to the agitator. It is made of tough plastic designed to withstand years of rotational torque without warping or cracking.  

Causes of a damaged washer sleeve can include regular wear from constant agitator motion. Mineral buildup accumulating inside over many wash cycles may cause interior components to deteriorate faster. Physical obstructions jamming the drive train could potentially bend or split the sleeve.

Symptoms of a failed sleeve involve:

• The agitator fails to rotate properly during cycles
• Grinding or squeaking noises coming from inside the washing machine
• Premature failure of connected parts like the drive belt or drive hub

This OEM replacement helps maintain the smooth operation of your washer's drive components. Compatible with some Kenmore and other Whirlpool-made top load models as well.

The Tub Bearing Kit is an OEM part for Whirlpool washers. It includes all the necessary components to replace the tub bearing which is responsible for supporting the inner tub and allowing it to spin smoothly during the wash cycle. Over time, the bearing may wear out or become damaged, leading to excessive noise, vibrations, or even leaks from the washer.

Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads or unbalanced loads that put excessive strain on the bearing, or damage due to water leaks.

Symptoms of a bad tub bearing include:

• Excessive noise or grinding during the wash cycle.
• Vibrations or shaking of the washer.
• Leaks from the washer, around the tub area.
• The inner tub not spinning or becoming stuck.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: It is advised to replace the Mounting Stem Repair Kit, part number 6-2040130 at the same time.  To complete the repair, you’ll also need a Spanner Wrench to complete the repair (TB123B).

The Water Inlet Valve is an OEM replacement part for Whirlpool washing machines. It is responsible for controlling the flow of water into the washer tub, ensuring the proper water level and supply for each wash cycle.

Causes of a bad water inlet valve can include sediment buildup or obstructions, electrical malfunctions, or normal wear and tear over time, leading to valve failure or improper operation.

Symptoms of a faulty water inlet valve include:

• The washer not filling with water or filling slowly
• Incorrect or inconsistent water levels during wash cycles
• Water leaks around the valve or inlet area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Siphon Break Kit is an OEM part for Whirlpool washing machines. This kit is designed to prevent backflow of water into the washer during the drain cycle, ensuring proper drainage and protecting the machine from potential water damage.

Causes of a bad siphon break can include wear and tear over time, blockages from debris, or damage from improper installation.  

Symptoms of a bad siphon break include:

• Water not draining properly from the washer
• Leaks or water pooling around the washer
• Unusual noises during the drain cycle
• Error codes related to drainage issues

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This small sleeve fits into the water/ice injector assembly to help guide and seal the water path. A worn or missing sleeve can lead to leaks, poor ice production, or water dispensing issues at the injector.

• Provides a sealed passage for water at the injector point
• Helps prevent drips and internal leaks near the dispenser/ice maker feed
• Resolves symptoms like leaking at the injector, weak ice fill, or irregular water flow
• Restores proper alignment and flow through the injector assembly

• Disconnect power and shut off the water supply before servicing
• Access the injector area per your model's service or user manual
• Note orientation of the original sleeve; press the new sleeve fully into place
• Check for secure tubing connections and verify no leaks after restoring water and power

For complete assembly order WP206680.

For complete assembly order WP206680.

This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.

• Seals the injector-to-liner/fill-tube connection to stop water seepage and air leaks
• Helps prevent frost/ice buildup near the injector area and fill tube freeze-ups
• Addresses issues from a cracked, shrunken, or missing seal
• Common symptoms: water drips at the back/freezer wall and frost near the fill opening

• Disconnect power and shut off the water supply before servicing
• Access the injector area (rear of freezer or cabinet, depending on model)
• Remove the old seal; press the new seal fully and evenly into place
• Reassemble, restore water/power, and check for leaks and proper fill

The Drain Hose is an OEM part for Whirlpool washing machines. It is responsible for carrying wastewater from the washing machine to the household drain system, ensuring proper removal of water during and after the wash cycle.

Common causes of a bad drain hose include wear and tear over time, blockages from debris or lint, and damage from sharp objects or improper installation.

Symptoms of a bad Drain Hose include:

• Water leaks from the hose
• Slow or incomplete drainage
• Visible cracks, splits, or punctures
• Unpleasant odors from trapped debris

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This internal hose connects the washer's outer tub to the drain pump, channeling wash water during the drain cycle. Replacing a worn or leaking hose helps prevent puddles and supports reliable draining performance.

• Routes water from the outer tub to the drain pump inside the washer
• Maintains a sealed path; cracks or loose connections can lead to leaks
• Visible splits, soft spots, swelling, or aging can cause water under the unit
• Obstructions or internal collapse may contribute to slow or incomplete draining

• Disconnect power and turn off water supply before servicing
• Expect residual water; use towels or a pan when removing the old hose
• Note hose routing and clamp positions; seat fully on each port and secure with appropriate clamps
• Run a quick fill/drain test and check all connections for leaks after installation

This replacement seal restores a tight, leak-resistant barrier between mating parts inside your appliance. Replacing a hardened or damaged seal helps stop seepage and keeps the system operating as designed. What it does:

• Forms a tight barrier between components to contain fluids and prevent leaks
• Helps maintain proper pressure/flow at the sealed joint
• Reduces risk of moisture damage around the connection point
• Common signs it's worn: drips or puddles, dampness around the joint, musty odors, visible cracking or flattening of the old seal

• 1 seal

• Disconnect power and shut off water or gas supplies before servicing
• Access the sealed joint; remove the old seal and clean mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved lubricant; install without twisting
• Reassemble, restore utilities, and check closely for leaks during initial operation

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This gasket creates a reliable seal between two appliance components. Replacing a worn or damaged gasket helps stop leaks and drafts at the joint, restoring proper performance and preventing moisture, frost, or debris from entering where parts meet.

• Forms a tight seal between mating surfaces to help prevent water or air leaks
• Helps maintain proper temperatures and operation by keeping unwanted air or moisture out
• Reduces vibration at the joint that can cause noise or loosening over time
• Typical failure signs: visible cracks or flattening, seepage or drips at the joint, moisture or frost forming nearby

• Disconnect power and shut off water supply before service
• Photograph the original setup to aid reassembly
• Remove the old gasket and thoroughly clean/dry both mating surfaces; remove any residue
• Seat the new gasket evenly without stretching; tighten fasteners evenly and check for leaks or air gaps after reassembly

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

This retaining washer secures a center-mounted component within the assembly, keeping parts aligned and in place during operation. Replacing a worn or missing washer helps prevent looseness, vibration, and noise for more reliable performance. What it does:

• Holds a component on a center shaft or stud to prevent axial movement
• Maintains proper alignment under rotation and load
• Can reduce wobble, rattling, or scraping noises from a shifting assembly
• In applicable washers, can help restore consistent agitation or spin when parts have been moving out of place

• 1 retaining washer

• Disconnect power and water before servicing; wear cut-resistant gloves
• Note the order and orientation of all spacers, washers, and clips during disassembly
• Clean mating surfaces and ensure the washer is fully seated before reassembly
• Inspect adjacent hardware for wear or damage and replace as needed