Dishwasher Upper Rack Roller Parts

This rear support wheel replaces a worn roller that helps a sliding drawer or rack glide smoothly and stay aligned. Restores easy, even movement and reduces dragging, scraping, or tilting during everyday use.

• Supports the rear of a sliding assembly on its track
• Provides smooth rolling action and helps maintain alignment
• Helps prevent binding, popping off the track, or uneven travel
• Replace if the wheel is cracked, flattened, missing, or if movement is noisy or difficult

• Disconnect power before servicing; allow the appliance to cool
• Remove the sliding assembly to access the wheel area
• Transfer or reinstall any axle/retainer from the original wheel as needed
• Verify smooth travel and proper alignment after replacement

Left side. For right side use part number WPW10251051.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

Color: White. This basket measures about 9 inches wide by 7 inches high by 6 inches deep. The cover and handle are not included. The cover is no longer available. For the handle order W11033847.

The Lower Rack Wheel is an OEM part for Whirlpool dishwashers. It attaches to the lower dishrack, allowing it to glide in and out smoothly during loading and unloading. For the matching wheel axle, order 4162321.

You should replace the lower rack wheel if it becomes worn out or damaged. Causes of a bad lower rack wheel can include regular wear and tear from frequent use, exposure to high temperatures and detergents, or physical damage from impacts or heavy loads. A faulty wheel can hinder the movement of the lower rack, making it difficult to access and load dishes properly.

Symptoms of a bad lower rack wheel include:

• The lower rack not sliding smoothly or getting stuck
• Uneven or lopsided positioning of the lower rack
• Noise or resistance when moving the lower rack
• The wheel appearing cracked, broken, or missing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This Rack Roller is an OEM part for Frigidaire dishwashers. It is an essential component for the smooth and stable movement of the dishwasher rack. 

Rack rollers can wear down or become damaged due to regular use, excessive load, or general wear and tear. A malfunctioning rack roller can make it difficult to slide the rack in and out, and may even cause the rack to become misaligned or unstable.

Symptoms of a failing rack roller in a dishwasher include:

• Difficulty in sliding the dishwasher rack in and out.
• A wobbly or unstable rack during movement.
• Unusual noises, such as scraping or squeaking, when the rack is moved.
• Visible wear or damage on the rollers.
• The rack getting stuck or not sitting properly in the dishwasher.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

This small retainer clip secures a mating part in the correct position inside your appliance, helping prevent movement, premature wear, and noise. Replace a cracked, bent, or missing clip to restore a tight, reliable hold.

• Provides a positive hold to keep the component properly seated
• Maintains alignment to reduce vibration and rattling during operation
• Helps prevent parts from backing out or disconnecting over time
• Common signs of failure: loose or misaligned component, rattling, clip that falls off, or visible damage

• Disconnect power; if working near any water connections, also shut off the water supply
• Note the clip's original orientation and position before removal
• Use needle-nose pliers or a small flat-blade screwdriver to release/install; avoid deforming mating tabs
• Ensure full engagement and that the secured part is firmly held before reassembly and testing

The Tine Row Holder is an OEM part for LG dishwashers. It is a molded plastic bracket located inside the dishwasher that firmly holds the horizontal tine rows of the upper spray arm assembly in place. Subject to vibrations during the wash cycle, the tine row holder must securely grip this assembly.

Symptoms of a bad tine row holder include:

• Loosened or detached upper spray arm that causes insufficient washing 
• Rattling noises from loose components inside the tub 
• Potential leaks if the plastic material cracks fully over time

Causes of failure can include cracking of the holder plastic from solvent exposure and mineral buildup over thousands of wash cycles. Replace with this OEM LG part to ensure balanced water distribution to all areas of dishes. It is also compatible with Sears/Kenmore dishwasher models.

This front leveling leg supports and adjusts the appliance at the front, helping it sit stable and truly level. Replace a damaged or missing leg to restore proper height, stability, and smooth door alignment during everyday use.

• Provides height adjustment at the front to level the appliance
• Helps prevent rocking, vibration, and rattling
• Maintains correct cabinet/door alignment for proper operation
• Replace if the foot is cracked, stripped, missing, or won't adjust
• Common signs: unit wobbles, sits unevenly, or is difficult to level

• Disconnect power; if applicable, shut off water or gas. Pull the appliance forward and remove the toe-kick/access panel for clearance.
• Protect the floor; tilt or raise the front slightly to reach the leg.
• Unscrew the damaged leg; thread the new leg in by hand to avoid cross-threading.
• Adjust height until level front-to-back and side-to-side; verify stability before returning to service.

This dishrack organizes and supports dishes inside the dishwasher during wash cycles. Replacing a damaged rack restores smooth loading, keeps items upright, and helps prevent rust stains or snags from broken tines or flaking rack coating.

• Holds and organizes plates, bowls, and cookware during wash and rinse cycles
• Keeps items spaced and upright to promote spray coverage and drainage
• Slides in and out on the rails when the rack is straight and intact
• Common failure signs: rusting/chipping coating, broken or bent tines, cracked or warped wire frame
• Needed if dishes won't stay put or the rack binds when moving on the tracks

• Disconnect power at the breaker and turn off water before servicing interior parts
• Open the door, extend the rack, and remove rail end caps to release the rack
• Transfer any clip-on components from the old rack to the new rack as needed
• Seat the rack on the rails, reinstall end caps, and check for smooth operation

The Dishrack Wheel is an OEM part for Whirlpool dishwashers. Each wheel works to smoothly guide the upper dishrack in and out of the dishwasher for convenient loading and unloading of dishes.

Causes of a bad wheel can include normal wear and tear from years of use or warping/bending due to overloading of the dishrack.

Symptoms of a bad dishrack wheel include:

• Noisy operation of the dishrack as it moves
• Difficulty fully extending or retracting the rack
• Binding or jamming that prevents smooth travel

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This upper rack wheel and axle assembly lets your dishwasher's top rack glide smoothly and stay level. Replace a cracked or missing wheel to fix hard-to-slide racks, scraping noises, or a rack that slips off the rail.

• Provides rolling support for the upper rack along the rails
• Helps keep the rack aligned to prevent sagging or derailment
• Replaces worn, cracked, or seized wheel assemblies
• Common symptoms: rack hard to slide, wheel wobbles/missing, grinding or scraping sounds, rack coming off track

• Disconnect power to the dishwasher for safety
• Pull out the upper rack and remove the rail end caps if needed
• Release and remove the damaged wheel/axle assembly from the rack
• Snap the new assembly into place, reinstall end caps, and test rack movement

The Rack Wheel is an OEM part for Whirlpool dishwashers. As an internal component that guides dish rack movement, the rack wheel works along the rack rail system to smoothly raise and lower racks in and out of the wash chamber. 

Causes of a bad rack wheel can include normal wear stripping lubrication from prolonged usage, or accidental impacts warping its circular shape.  

Symptoms of a bad rack wheel include: 

• Difficulty pulling out or pushing in dish racks  
• A rack that gets stuck and does not fully recline or rise
• Rack trays that cannot pivot to different levels during a cycle
• Reduced wash effectiveness from poor rack positioning

This OEM Whirlpool part is also compatible with some Maytag, KitchenAid, and GE dishwashers.

Used on the upper dishwasher dishrack.

The Silverware Basket is an OEM component specifically designed for Whirlpool dishwashers. Located at the bottom outer edge of the tub, the silverware basket provides designated silverware basket dishwasher spacing to properly clean utensils away from other dishes. 

Composed of crisscrossing finger prongs attached to a reinforced circular base, the basket holds forks, knives, and spoons upright safely in place during wash cycles. Its lightweight plastic construction flexes under pressure without breaking or cracking.

Symptoms of a bad silverware basket include:

• Loose or falling utensils obstructing other spray jets   
• Dull or improperly cleaned silverware after cycles
• Visible cracks, chunks missing, or sharp prongs

Replace with this OEM Whirlpool basket to restore form-fitting function. This part fits Whirlpool, KitchenAid, Jenn-Air and select Maytag and Amana dishwashers.

This float stem is part of the dishwasher's water-level/overfill system. It guides the tub float and actuates the float switch so the unit fills correctly and shuts off on time. Replace a worn or broken stem to restore reliable fill protection.

• Connects the float to the switch mechanism beneath the tub
• Provides smooth vertical travel of the float through the opening
• Triggers the float switch to stop filling at the proper level
• Causes symptoms such as no fill, continuous filling/overfilling, a stuck or wobbly float, or intermittent fill issues

• Disconnect power at the breaker and shut off the water supply before servicing
• Remove the lower rack; lift off the float cap from inside the tub
• On some models, release the retainer/clip from beneath the tub; pull out the old stem
• Guide the new stem through the opening and ensure it engages the float switch lever; confirm the float moves freely and actuates the switch before restoring power