Dryer Power Strike Small Engine Regular Starter Parts

This thermostat is a temperature-sensitive switch used in the appliance's heating circuit. It opens and closes at a specific temperature to regulate or limit heat, helping maintain correct operation and protect components from damage due to overheating.

• Monitors temperature and switches the heating circuit on/off at its preset trip point
• Helps prevent overheating and heat-related component damage
• Failure symptoms can include no heat or underheating, overheating or burnt odors, or heat that won't shut off
• May cause intermittent heating or frequent cycling as the unit warms and cools

• Disconnect power and allow the appliance to cool completely; shut off gas supply if applicable
• Access the thermostat, note/photograph wire positions, and transfer wires one at a time to the new part
• Mount securely against the proper surface/bracket so the sensor has good contact
• Restore power and test operation; if issues persist, diagnose related heating components per the service manual

This safety thermostat monitors temperature at the dryer's air inlet and opens the heater circuit if temperatures climb too high. Replacing a failed unit restores proper heat control and helps protect the dryer from overheating damage. What it does:

• Senses inlet air temperature and interrupts power to the heater when a high limit is reached
• Helps prevent overheating and repeat thermal fuse failures due to restricted airflow
• Failure symptoms include no heat, intermittent heat, very hot cabinet, or a burnt odor
• Supports consistent drying performance by maintaining safe operating temperatures

• 1 thermostat

• Disconnect power; turn off gas supply for gas models
• Thermostat is typically mounted on the inlet duct or near the heater/blower housing; refer to your model's diagram for location
• Move wires one at a time to the new thermostat; reuse existing mounting hardware
• After replacement, clean the lint path and verify proper vent airflow to prevent repeat failures

The Dryer Door Catch Lever Assembly is an essential component for maintaining the functionality of your Samsung dryer. This genuine OEM part ensures that your dryer door closes securely every time, preventing unwanted openings and maintaining optimal drying performance. Crafted with high-quality materials, the assembly holder lever is designed for durability and long-lasting use, effectively withstanding the daily wear and tear of appliance operation. Installing the Dryer Door Catch Lever Assembly is straightforward, allowing you to quickly restore your dryerGÇÖs performance without the need for professional assistance. This part is specifically compatible with a range of Samsung dryer models, ensuring a perfect fit and seamless integration with your existing appliance. By choosing this genuine OEM part, you can be confident in the reliability and performance of your dryer, enhancing its overall efficiency and extending its lifespan. Whether replacing a broken or malfunctioning door catch, the Dryer Door Catch Lever Assembly provides a dependable solution to keep your laundry routine running smoothly.

This thermostat monitors temperature and opens or closes its electrical contacts to control and protect the appliance's heating circuit. Replacing a failed thermostat restores stable temperatures and helps prevent nuisance shutdowns or persistent no-heat issues. What it does:

• Senses temperature at its mounting location and switches the circuit on/off as designed
• Protects the heating system by interrupting power when temperatures exceed its rated limit
• Helps maintain consistent operation when the original thermostat is stuck open/closed or out of calibration
• Typical symptoms: no heat or intermittent heat, overheating/safety shutdowns, or failed continuity when tested cool

• 1 thermostat

• Disconnect power (and shut off gas supply if applicable) before servicing
• Note wire locations and transfer one at a time to the new thermostat
• Mount securely in the original position to ensure proper temperature sensing
• After installation, run a test cycle and monitor operation/temperature

This thermal limiter (89°C) is a one-time, temperature-sensitive safety device that opens the circuit if internal temperatures rise too high. Replacing a failed limiter helps protect the appliance from overheating and can restore normal operation. What it does:

• Monitors temperature in the airflow/heating path and opens around 89°C to interrupt power when overheating occurs
• Helps protect wiring, controls, and heater components from thermal damage
• A blown/open limiter can cause: appliance won't start, no heat, or stops mid-cycle
• Often indicates an underlying overheating issue that should be corrected

• 1 thermal limiter

• Disconnect power (and gas supply if applicable) and allow the unit to cool before servicing
• Access the limiter per the service information; note wire positions and transfer leads one at a time
• Replace only with the correct rated limiter; never bypass this safety device
• After installation, clear airflow restrictions and verify proper venting and heater/thermostat operation

The door switch detects whether the dryer door is open or closed, enabling the motor and heater only when it's safe. Replacing a failed switch restores proper start/stop control and drum light behavior.

• Senses door position and completes or interrupts the dryer's run/heat circuits
• Shuts the dryer off when the door opens for safety
• Common symptoms: dryer won't start with the door closed; doesn't stop when door opens; drum light stays on or won't turn on
• Intermittent operation when the door is moved or pressed

• Disconnect power before servicing; allow components to cool
• Access the switch from the door opening or front panel; remove screws or release locking tabs
• Note wire positions and transfer them one at a time to the new switch
• Verify operation before reassembly: dryer should not run with the door open; drum light should respond

This dryer thermostat monitors internal air temperature and opens/closes the heater circuit to keep drying safe and consistent. Replacing a weak or failed thermostat restores proper heat and helps prevent overheating or nuisance shutdowns. What it does:

• Senses exhaust/heater housing temperature and switches the heating circuit based on temperature
• Helps maintain target drying temperatures for consistent performance
• Provides over-temperature protection by opening the circuit if heat rises too high
• Common symptoms include no heat or weak heat, long dry times, heat cutting out mid-cycle, or the dryer running hotter than normal

• 1 thermostat

• Disconnect power before servicing; heating components can be live and hot
• Access location varies by model; typically mounted on the heater or blower housing behind a rear or front panel
• Transfer wires from the old thermostat to the new one one-at-a-time and secure firmly; ensure the mounting surface is clean and flat
• After replacement, check and clear the venting/duct for proper airflow to prevent repeat failures

This sensor monitors humidity inside the microwave cavity so sensor-cook and reheat features can automatically adjust time and power. Replacing a failing sensor restores accurate automatic cooking and helps prevent premature shutdowns or "Sensor" error messages.

• Detects steam/humidity in the cavity during sensor-based cooking cycles
• Sends feedback to the control to optimize cook time and power levels
• Failure can cause "Sensor" errors, sensor-cook cycles that won't start or end early
• Manual timed cooking may still work while sensor-cook modes misbehave

• Disconnect power before servicing; microwaves contain a high-voltage capacitor that can retain a dangerous charge
• Access is typically behind the top grille/control area; note sensor orientation before removal
• Handle the sensor by its body; avoid contaminating the sensing face
• Route wiring as original and ensure the connector is fully seated before reassembly

This outlet backup thermostat for dryers mounts on the exhaust duct and provides secondary over-temperature protection. It shuts the heater off if exhaust air gets too hot, helping maintain safe, consistent drying.

• Serves as a secondary temperature limit on the exhaust/outlet duct
• Opens the heater circuit if exhaust temperature rises too high
• Failure symptoms include no heat, intermittent heat, overheating, or short-cycling
• Replace if it fails continuity testing or shows heat damage

• Disconnect power and shut off gas supply (for gas models) before servicing
• Access the outlet/exhaust duct per your model; transfer wires one at a time and secure the thermostat to the duct
• Replace any heat-damaged connectors and correct restricted airflow (clean lint filter and vent) before testing
• Match the color/rating to your original; this is the orange variant

This power relay is an electromechanical switch with a 48 VDC coil that lets the control board safely turn high-voltage components on and off. Replacing a weak or sticking relay helps restore consistent, reliable operation. What it does:

• Uses a 48 VDC coil signal from the control to open/close internal contacts
• Switches AC line power to high-demand loads (e.g., heater, motor, fan, or compressor)
• Helps maintain stable cycling and prevents intermittent operation
• Helps with symptoms such as no heat or no run, intermittent operation, clicking with no activation, or a component stuck on

• Power relay (48 VDC coil)

• Disconnect power to the appliance before servicing; allow capacitors to discharge
• Note/photograph wire locations and move wires one at a time to matching terminals
• Ensure terminals are fully seated; replace any burnt or loose connectors
• Mount in the original orientation and secure firmly to prevent vibration

This cycling thermostat regulates your dryer's internal air temperature by switching the heat source on and off, helping prevent overheating and keeping drying performance consistent. Replace it if temperatures are erratic, items run too hot, or dry times increase. What it does:

• Monitors drum air temperature and opens/closes to control the heater
• Maintains stable temperatures across fabric/temperature settings
• Failure symptoms include no or low heat, overheating/scorch smells, long dry times, or inconsistent cycling
• Helps protect against damage from excessive heat when functioning correctly

• 1 cycling thermostat

• Disconnect power; if it's a gas dryer, also shut off the gas supply
• Allow the unit to cool; access the thermostat (typically on an internal air duct or blower housing); note wire positions
• Transfer wires to the new thermostat one at a time; mount flush against the metal surface; do not overtighten
• After installation, clean lint passages and ensure proper airflow and temperature control

This broken belt switch is a dryer safety switch that senses drive belt tension and opens the motor circuit if the belt breaks or slips off. Replacing a failed switch can resolve a no-start or no-tumble condition. What it does:

• Monitors drive belt tension via the idler assembly
• Interrupts power to the motor when the belt is broken or not tensioned
• Helps prevent heating without airflow when the belt has failed
• Symptoms can include: dryer won't start, drum won't turn, or the dryer stops as soon as the Start button is released

• 1 switch

• Disconnect power; for gas models, shut off the gas supply
• Access the switch near the idler pulley by removing the lower/front panel per your model
• Transfer wires from the old switch to the new one; mount securely with the actuator aligned to the idler arm
• Run a brief test cycle

This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.

• Provides overcurrent protection for the circuit specified by the manufacturer
• If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
• Helps prevent wiring and component damage from shorts or overloads
• Repeated fuse failures indicate an underlying electrical issue requiring diagnosis

• Disconnect power to the appliance before servicing
• Locate the fuse in its holder/block and inspect associated wiring for heat or damage
• Test the old fuse for continuity; replace only with the identical rating specified
• Never bypass or upsize a fuse; correct the root cause of the failure before returning to service

The Whirlpool Dryer Door Catch is an OEM part for Whirlpool dryers. It secures the dryer door closed during operation, ensuring the safety and proper functioning of the appliance. This component engages with the door latch to hold the door shut, allowing the dryer to operate without interruption.

Causes of a bad dryer door catch can include normal wear and tear from frequent use, accidental damage, or deformation of the catch or latch that prevents proper engagement. Over time, the door catch can become loose or break, necessitating replacement to maintain the dryer's performance and safety.

Symptoms of a bad dryer door catch include:

• The dryer door not staying closed during cycles
• Difficulty closing the door securely
• The dryer stopping mid-cycle due to the door opening

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This thermistor is the temperature-sensing component that feeds accurate readings to the appliance's control. Replacing a faulty sensor restores proper temperature feedback, helping the control run cycles correctly and reduce temperature-related performance issues. What it does:

• Monitors temperature and changes resistance with temperature (NTC), sending a signal to the control board
• Helps the control regulate heating or water-temperature management during operation
• When open/shorted or out of range, can trigger temperature/sensor error codes
• Symptoms include inconsistent temperatures, long run times, or cycles that won't complete

• 1 thermistor

• Disconnect power before servicing; shut off gas/water supply if applicable
• Access the sensor per your model; it's typically secured by a clip or screw and connects via a wire harness
• Note wire orientation; avoid pulling on wires and ensure the connector is fully seated
• After installation, clear any stored error codes and run a diagnostic or test cycle

This door catch assembly secures the door by engaging the mating latch or strike, keeping it firmly closed for proper operation and safety. Replace a worn or broken catch to restore reliable door closure and consistent performance. What it does

• Engages the door latch/strike to hold the door closed during use
• Helps maintain proper door alignment and contact with seals/interlocks
• Restores a positive latch feel and consistent closure
• Common signs of wear: door won't latch or pops open, must be slammed to close, visible damage to catch tabs

• One door catch assembly

• Unplug the appliance or switch off power at the breaker before servicing; for gas appliances, shut off the gas supply
• Open the door, access the catch at the cabinet/frame, and remove retaining screws or clips
• Transfer any reusable hardware from the original part and install the new catch
• Verify smooth latch engagement and door alignment before restoring power