Refrigerator Control Panel Lcd Parts

Color: Grey

The Cold Control is an OEM part for Frigidaire refrigerators. It plays a key role in regulating the refrigeration cycle and maintaining optimal temperatures inside the refrigerator and freezer compartments. The cold control sensor monitors interior conditions and signals the compressor and condenser fan module to turn on or off accordingly.

Causes of bad cold control can include fatigue of internal components from repeated cycling over the refrigerator's lifespan, mineral or moisture buildup affecting sensors and circuitry, or failure due to sudden temperature fluctuations. 

Symptoms of a bad cold control include:

• Inconsistent or fluctuating temperatures within compartments
• The refrigerator or freezer running constantly 
• Food not staying freshest as long as expected
• Frost or ice buildup inside that is difficult to remove

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This part shields and positions the temperature control's sensing bulb inside the control housing, helping the control respond accurately and keep cabinet temperatures stable. Replace a cracked, deformed, or missing barrier to restore consistent, predictable cooling. What it does:

• Shields the cold-control thermostat/capillary bulb from direct airflow
• Helps the temperature control sense average compartment temperature and cycle correctly
• Supports steady temperatures and normal run times
• A damaged or missing barrier may contribute to temperature swings or frequent control adjustments

• 1 thermostat barrier

• Disconnect power before servicing
• Access the control housing; remove the dial/cover and any retaining screws or clips
• Note the factory routing of the thermostat capillary; install the barrier without kinking or sharply bending the sensor tube
• Reassemble, set controls to mid-range, and allow up to 24 hours for temperatures to stabilize

Restore a tight, even seal between your refrigerator's doors. This vertical mullion assembly flips into place to cover the center gap, helping maintain proper temperatures and reduce condensation.

• Bridges the gap between doors to create a continuous sealing surface
• Helps keep cold air in and warm air out for consistent cooling
• Aids proper door alignment and smooth closing
• Common symptoms of a failed mullion: broken or wobbly flipper, doors not closing fully or popping open, moisture/icing at the center, warming in the fresh food section

• Disconnect power before servicing and open the doors
• With the door open, release the retaining screws or tabs and lift the old mullion off the upper and lower pivots
• Position the new assembly on the pivots, secure it, and verify the flipper moves freely and seals evenly against the opposite door
• Restore power and recheck door operation and gasket contact along the full height

This thermostat is a temperature safety device that opens the circuit if temperatures climb beyond the safe threshold. Replacing a failed thermostat helps protect the appliance from overheating and restores normal heating performance.

• Monitors internal temperature and cuts power if it overheats
• Helps prevent damage to components from excessive heat
• Common failure signs include no heat, intermittent heat, or the unit shutting off on high heat
• Shows continuity when cool and open when tripped

• Disconnect power before service; verify no voltage is present
• Access location varies by model; note wire positions and transfer one at a time
• Mount firmly against the intended surface for proper sensing
• After replacement, verify airflow/venting and clear lint/debris to avoid repeat trips

This thermostat is a temperature-sensitive safety switch that monitors heat and opens or closes the circuit at a set point. Replacing a failed thermostat restores reliable temperature protection and corrects issues caused by tripping or stuck contacts.

• Monitors component/cavity temperature and trips at a preset limit
• Opens (or closes) the electrical circuit to prevent overheating or activate cooling functions
• Common symptoms: no heat or intermittent heating, unit won't start or shuts off during use, cooling/vent fan runs constantly or never turns on
• Useful diagnostic clue: faulty thermostats may test open or stuck closed at room temperature

• Disconnect power at the breaker before servicing; if used in a microwave, be aware the high-voltage capacitor can retain a dangerous charge
• Note wire locations; transfer one lead at a time and secure the thermostat in the original mounting position for proper sensing
• Ensure clean metal-to-metal contact with the mounting surface; do not overtighten screws
• After installation, restore power and verify normal operation

This main power control board assembly is the refrigerator's central controller. It manages power to the compressor, fans, and defrost system so the unit cools consistently and responds correctly to temperature settings.

• Distributes and regulates power to the compressor, condenser/evaporator fans, and defrost components
• Processes inputs from temperature sensors and the user interface to coordinate cooling cycles
• Common symptoms it may address: not cooling or intermittent cooling, fans/compressor not running, unit won't defrost/ice buildup
• May also help with unresponsive controls or repeated clicking/buzzing from the control area

• Disconnect power before servicing; handle the board by the edges and use ESD protection
• Access location varies by model; typically mounted in a rear control compartment behind an access cover
• Photograph wiring and move connectors one at a time to the new board; ensure all locking tabs are fully seated
• Reinstall covers, restore power, and verify compressor/fans operate and cooling resumes

The Refrigerator Power Control Board is essential for maintaining the efficient operation of your refrigerator. This genuine OEM part ensures reliable performance by managing the electrical functions and regulating temperatures accurately. Compatible with a wide range of Samsung refrigerator models, it guarantees a perfect fit and seamless integration. The PCB Assembly Inverter design offers precise control over cooling cycles, enhancing energy efficiency and extending the lifespan of your appliance. By replacing a faulty power control board with this high-quality component, you can resolve issues such as inconsistent cooling, malfunctioning displays, or irregular compressor activity. This not only restores your fridge's functionality but also helps you avoid costly service calls. Easy to install, the Refrigerator Power Control Board allows for a straightforward DIY repair, empowering you to maintain your appliance with confidence. Trust in this genuine OEM part to deliver dependable performance and keep your refrigerator running smoothly, ensuring your food stays fresh and your kitchen operates efficiently.

The Refrigerator French Door Assembly is designed to seamlessly replace the doors on your Samsung French door refrigerator. Crafted as a genuine OEM part, this assembly ensures a perfect fit and maintains the integrity of your appliance. The durable construction provides reliable performance, helping to keep your food fresh and organized. With its sleek design, the Refrigerator French Door Assembly not only restores the functionality of your fridge but also enhances its overall appearance. Compatible with a variety of Samsung refrigerator models, this assembly allows for easy installation, saving you time and effort. Whether your original doors are damaged, cracked, or worn out, the Refrigerator French Door Assembly offers a straightforward solution to restore your refrigerator to its optimal condition. Invest in this genuine OEM part to ensure long-lasting quality and maintain the efficiency of your Samsung refrigerator, providing you with a dependable and attractive kitchen appliance.

This mechanical thermostat monitors temperature and opens or closes the circuit at a fixed set point to control heat and prevent overheating. Replacing a failed thermostat restores safe operation and consistent performance. What it does:

• Senses surface or component temperature and switches the circuit at a calibrated threshold
• Helps protect heaters, motors, and controls from thermal damage due to over-temperature
• Common symptoms of failure: no heat, shuts off mid-cycle, won't start until cooled, or intermittent operation
• Restores proper temperature control after a thermostat sticks open/closed or drifts out of spec

• 1 thermostat

• Disconnect power at the breaker (and shut off gas, if applicable) before servicing
• Note wire positions and transfer leads one-for-one to the new thermostat
• Mount flush against the sensing surface with original screws/clips; reinstall any insulation or thermal interface material as found
• Correct the root cause (blocked vents, failed fan, restricted airflow, or buildup) before returning the appliance to service

This is a control board for refrigerators. The control board governs the main functions of the appliance, such as cooling and defrosting.The most prevalent sign of a damaged control board is the noticeable elevation of the temperature inside the refrigerator compartments. The refrigerator may also stop defrosting properly, which can lead to leaking and other issues with the appliance. Begin the installation by unplugging the refrigerator from its main power source. Locate the control board panel on the back-right corner of the appliance. Remove the housing screws and slide the access panel off. Unplug the wires to the control board and remove the mounting screws. Repeat these steps in reverse to install the new control board.This control board is a genuine OEM product sourced directly from the manufacturer. The control board is only available individually and does not include any other components. This product is compatible with GE appliances.

The Dispenser Control Board is an OEM part for Frigidaire refrigerators featuring interior dispensers. It oversees dispensing of ice and water according to user selection. Located within the refrigerator door panel, it activates motors and solenoids.

Symptoms of a bad dispenser control board include:  

• Inability to dispense ice or water from lever/button
• Dispenser motors or solenoids not activating properly   
• Unresponsive or stuck dispenser lights and selection buttons
• Water or ice volumes not measured accurately

Causes can be long-term moisture exposure degrading circuitry or power surges overloading sensitive components. Proper drying and periodic cleaning help prevent issues.

This genuine OEM control board is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

This ice compartment door closes off the ice storage area inside the freezer, helping contain cold air and keep ice clean. Replace a cracked or warped door to restore a proper seal and easy access to the bin.

• Covers the ice compartment opening to help maintain temperature around the ice bin
• Hinged panel provides convenient access to the ice container
• Helps minimize frost and moisture at the compartment opening
• Common signs it's needed: cracked/missing door, broken hinge tabs, won't stay closed, frost buildup, or ice clumping near the opening

• Disconnect power to the refrigerator before servicing
• Remove screws, pins, or clips securing the old door; note hinge orientation
• Transfer any reusable hinge pins, latches, or trim from the original if required
• Install and align the new door; confirm smooth operation and a tight closure

Restore accurate cooling with this refrigerator temperature control thermostat. The cold control senses compartment temperature and opens or closes the circuit to cycle the cooling system, helping maintain your selected setting when the original control becomes unreliable.

• Monitors refrigerator air temperature via a sensing bulb
• Opens/closes electrical contacts to cycle the cooling system
• Maintains the temperature you select with the control knob
• Common symptoms of a failing control: temperatures too warm or too cold, refrigerator runs constantly or won't start, no response to knob adjustments

• Disconnect power to the refrigerator before servicing
• Access the control housing and note wire locations and the exact routing/placement of the sensing bulb
• Transfer any mounting hardware and the control knob from the old part; install the new thermostat
• Route and secure the sensing bulb exactly as original—do not kink the capillary; restore power, set to a mid setting, and allow temperatures to stabilize before fine-tuning

The Refrigerator French Door Guide is essential for maintaining the smooth and stable operation of your French door refrigerator. This genuine OEM part is specifically designed for Samsung refrigerator models, ensuring a perfect fit and optimal compatibility. Crafted from high-quality materials, the guide provides robust support and precise alignment for your refrigerator doors, reducing wear and tear and extending the lifespan of your appliance. Easy to install, this part allows you to restore functionality without the need for professional assistance, saving you time and effort. The Refrigerator French Door Guide helps maintain proper door alignment, which not only enhances the aesthetic appeal of your kitchen but also improves energy efficiency by preventing air leaks and drafts. Additionally, it ensures that the doors open and close effortlessly, enhancing your overall user experience. If your original door guide is damaged, worn, or no longer functioning correctly, this genuine OEM part is the ideal solution to keep your Samsung refrigerator operating smoothly and efficiently. Invest in the Refrigerator French Door Guide to ensure reliable performance and prolong the lifespan of your appliance.

This is a high-quality refrigerator power supply board. It's an internal component that is made to control the refrigerator functions. This part is made with small precision parts to help with timing defrost and cooling cycles. This part can be damaged or malfunction and stop operating correctly. This may prevent the refrigerator from running, cause strange sounds, or cause the refrigerator to run at the wrong temperature.If this part is damaged, it will need to be replaced. Before replacing the power supply board, make sure the refrigerator is unplugged from the wall. The process will require a flathead screwdriver and a nut driver. Use the tools to unthread the screws on the access cover. Depress the retaining tab to remove the inner cover and disconnect the wires. Press the tab to release the power supply board and snap in the new component. Make sure the wires are properly connected and reassemble.This genuine OEM replacement part is sold on an individual basis. It is directly acquired from the manufacturer and is designed to be compatible with refrigerators made by Kenmore, Whirlpool, Maytag, and KitchenAid.