110-23442500 Parts

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

This mechanical timer is the cycle control for select top-load washers. It sequences power to the motor, drain pump, and inlet valve so the machine advances through fill, wash, rinse, drain, and spin as designed.

• Controls the timing and order of each wash cycle step
• Sends power to components at the correct times
• Advances the cycle via an internal cam and timer motor
• Common symptoms: won't start or won't advance, stops mid-cycle, runs too long, or the timer knob doesn't move

• Disconnect power before servicing
• Access the control console; remove the dial/knob and mounting screws to release the timer
• Photograph wiring and transfer leads one-for-one to the new timer
• Reinstall, reassemble the console, and test operation

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Hose used from Valve to thermistor.

This knob insert is the small piece that snaps into a control knob. It restores a clean, finished look when the original insert is cracked, discolored, loose, or missing.

• Provides the insert for a control knob to replace a worn or missing piece
• Snaps in for a secure, factory-style fit
• Helps keep dust and debris out of the knob cavity
• Typical symptoms: knob center missing, insert cracked, loose, or discolored

• Disconnect power before servicing the control panel
• If needed, pull the knob straight off the shaft to access the insert
• Gently pry out the old insert; avoid metal tools that can mar the finish
• Align tabs and press the new insert flush until it clicks into place

This agitator assembly restores factory wash action in your top-load washer, driving clothes rollover and detergent circulation so loads clean evenly. Replace a cracked, loose, or slipping agitator to bring back reliable movement.

• Provides the back-and-forth motion that rolls clothes through the wash water
• Promotes even cleaning by circulating water and detergent
• Common symptoms: no or weak agitation; upper agitator freewheels in one direction; clicking/ratcheting during wash
• Also used when the agitator is visibly cracked, loose, or damaged

• Disconnect power and turn off water supply before servicing
• If equipped, remove the fabric softener dispenser and cap to access the retaining bolt; lift the old agitator straight up
• Align splines, seat the new agitator fully, and reinstall the retaining bolt and cap
• Reuse any model-specific caps/dispensers and run a short test cycle to ensure proper agitation

This agitator cam is the replacement cam that fits under the washer agitator to engage the transmission and help transfer motion. Replacing a worn or broken cam restores secure agitator engagement for reliable washing action. What it does:

• Locks the agitator to the drive so the agitator oscillates and reverses during wash cycles
• Replaces a damaged or worn cam that can cause the agitator to slip, spin freely, or fail to agitate
• Works with the agitator assembly and dogs to maintain proper drive engagement
• Restores proper mechanical linkage between the agitator and the washer transmission

• Disconnect power and water supply before beginning any repair
• Remove the agitator, inspect agitator dogs and splines for wear, and replace if needed
• Install the cam into the agitator and reassemble in reverse order of removal following the OEM service instructions
• After reassembly, run a short test cycle to ensure the agitator engages and functions correctly

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

Includes connector and both clamps.

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely