11042926200 Kenmore Washer Parts

• Won't start

Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since. Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Several months back, I checked the supply hoses and replaced the hot water hose because of corrosion. The cold water hose was fine. I replaced the water inlet valve and that seemed to fix the problem, but after about a week, the problem resurfaced. After searching various internet resources, I though the pressure switch which detects the water level could be bad. I order both the pressure switch and the hose that connects it to the air chamber. Before installing the new pressure switch, I... Read more

• Lid or door will not open
• Lid or door won't close
• Won't start

New inner drum and front and rear outer drum; although other parts worked, still replaced the bellow and clamp, new door latch, and cleaned the hoses. Washer works great. Just like brand new. Even though matching dryer works, I am going to clean it up and replace some parts on it also. Read more

• Leaking

We ordered parts from appliance parts pros and I fixed it. Read more

I pulled the unit away from the wall and noticed black dust on the floor. Unplugged the unit, turned off the water. Removed back panel (about 10 screws with Torx heads) and noticed the belt was off, the drive pulley was loose and wobbling on the shaft, black dust all over the inside. Belt was worn along one side. Some grooves/damage in the outer drum casing around the pulley where it appeared the belt had rubbed. Removed the lower crossbar (2 more screws) to get better access to the drive... Read more

After troubleshooting the problem I checked online for similar issues and how they were resolved. I discovered the video on YouTube for replacing the wash tub boot. Although the video was for a Whirlpool washer it turned out to be spot on for my Kenmore Elite. The breakdown and removal of the torn boot was bolt for bolt perfect. I ordered the part direct from Appliancepartspros.com on a Sunday night and it arrived by Tuesday afternoon. I watched the same video over, replaced the boot then... Read more

We started getting the F06 code when on the normal cycle it was time to Rinse/Spin, pointing to a speed/tachometer issue on the motor. After several attempts of unplugging from power and restarting the cycle it would eventually start working for the rest of the laundry session. The Whirlpool technician after a brief look on the underside determined it was the motor and had to be replaced, even tough all troubleshooting tests on the motor were ok. I insisted that the probability was much higher... Read more

Had to buy a new draw handle and detergent draw..they attach together by two plastic tabs that take a lot of stress each time you open it..unfortunately had to buy both to fix the problem.. Read more

I ordered the dispenser and the distribution nozzle since the old one was in bad shape. I also replaced the boot since I had to take the entire machine apart and it is 20 years old. I watched your videos on you tune to learn what to do. I recently lost my job and really could not afford to hire someone to fix my washer. I have to say it wasn't that hard to do and my wife was so happy that I was able to fix it myself! I probably saved $200 or $300 in service calls and labor on top of what they... Read more

Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ... Read more

The replaced hose from the dispenser and o-ring problem fixed. Read more

The shipping bolts came in 2 days!!! Wow ! So we watched a video on how to install them and moved the washer without messing it up.. Thank you so much for fast and friendly service :-) Read more

I temporarily fixed the hole with electrical.tape until I received my part from appliancepartspros. I then made the required repair. Read more

The replacement part and YouTube video allowed me to repair my washer in less than 10 minutes. Read more