22-13742 Parts

Gasket for upper wheel.

This door latch strike is the catch mounted at the top of the dishwasher tub opening. It provides a secure engagement point for the door latch, helping the door close firmly so cycles can start and run properly. What it does:

• Serves as the latch catch on the tub/frame for the door latch to lock onto
• Helps ensure the door switch engages so the dishwasher will start
• Restores proper door alignment and closure if the original strike is bent, loose, or missing
• Common symptoms include door won't latch/close, dishwasher won't start, or door popping open mid-cycle

• 1 door latch strike

• Disconnect power at the breaker and turn off the water supply before servicing
• Open the door and remove the mounting screws securing the old strike
• Position the new strike, start screws by hand, and adjust so the latch engages smoothly; then tighten
• Test door closure several times and run a short cycle to ensure proper operation

The Steam Vent is an OEM part for Whirlpool dishwashers. It is designed to allow steam to escape from the dishwasher during and after the washing cycle, preventing excessive moisture buildup inside the appliance.

Causes of a bad steam vent can include clogs due to mineral deposits or food particles, damage to the vent mechanism from repeated use or accidental impact, and wear over time that affects its sealing capability. A malfunctioning steam vent can disrupt the dishwasher’s drying process and lead to poor performance.

Symptoms of a bad steam vent include:

• Excessive moisture or condensation inside the dishwasher
• Poor drying performance
• Noticeable steam escaping from areas other than the designated vent
• Unusual noises during the drying cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This mounting bracket secures an appliance component in the correct position, providing stable support and alignment. Replacing a damaged bracket helps stop looseness and vibration that can lead to noise, poor fit, or premature wear.

• Provides a rigid mounting point to hold the related assembly in place
• Restores proper spacing and alignment for consistent operation
• Helps reduce rattling, buzzing, or vibration from movement
• Replaces cracked, bent, or corroded brackets that no longer hold securely

• Disconnect power; shut off water supply if applicable
• Note the original orientation; transfer any clips, spacers, or grommets from the old bracket
• Reuse existing screws/fasteners; hand-start threads to avoid cross-threading
• Do not overtighten fasteners; confirm clearance and smooth operation before reassembly

The Upper Wash Arm Support is an OEM part for Whirlpool dishwashers. It provides structure and stability to the upper wash arm as it rotates during the wash cycle. This support ensures effective spray coverage from the upper wash arm reaches all corners of the dish rack above. 

Causes of a bad wash arm support can include wear and tear from normal use over time, or damage from loading large or sharp items into the dishwasher that impact the wash arms.

Symptoms of a bad wash arm support include: 

• The upper wash arm not rotating or spinning properly 
• Insufficient spray pattern and cleaning from the upper arm
• Noises or vibrations coming from the upper wash system
• Leaks or pooling of water inside the dishwasher 

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This overfill control float sits in the dishwasher tub and rises with the water level to signal the float switch to stop filling. Replacing a cracked or sticking float helps prevent leaks and recurring fill issues. What it does:

• Rises with the water level to actuate the float switch and stop the inlet valve
• Helps prevent overfilling and water leaking from the door
• A float stuck in the UP position can cause no fill or short fill
• A float stuck DOWN or damaged can allow overfilling

• 1 overfill control float

• Disconnect power and turn off water before servicing
• Remove the lower rack; lift out the old float from its guide and clear any debris in the well
• Insert the new float, ensuring it moves freely and reliably actuates the switch when raised

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This wheel mount assembly fits the dishwasher's upper rack track and provides the roller that lets the rack glide in and out. Replacing a worn or broken mount restores smooth movement and keeps the rack aligned on the rails. What it does:

• Supports and guides the upper rack along the side rails
• Replaces cracked, missing, or seized rollers that make the rack hard to slide
• Helps prevent the rack from popping off the track or sitting unevenly
• Can reduce scraping or squeaking noises when moving the rack

• One upper rack wheel mount assembly

• Disconnect power to the dishwasher before servicing
• Open the door and remove the upper rack by releasing the rail stops
• Depress the locking tab to remove the old wheel mount from the rail; align and snap the new assembly into place
• Reinstall the rack and rail stops; check for smooth rack travel

Quantity of ONE. Size: 8-18 x 5/8 inch. (#8 screw, 18 threads per inch, 5/8 inch long)

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

Note: Right Hand side with release lever.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This vent housing assembly mounts in the dishwasher door to guide humid air out of the tub. A secure, sealed housing helps prevent steam leaks and moisture damage while supporting proper airflow during the dry portion of the cycle.

• Provides a sealed mounting point for the door vent
• Channels moist air out during drying to protect the door and control panel
• Helps prevent steam or moisture from escaping at the top of the door
• Common symptoms: steam or dampness at the door top, water streaks on the front panel, or visible cracks/warping in the housing

• Disconnect power at the breaker and turn off water supply before servicing
• Remove inner door panel fasteners to access the vent area
• Note orientation; transfer any gasket or retainers from the original housing if required and seat the new housing flush
• Reassemble and run a short cycle to check for leaks and proper airflow

This small clip secures the guard/shield on the dispenser assembly. Replacing a cracked or missing clip keeps the guard firmly attached and aligned so the dispenser operates properly without interference, noise, or premature product loss. What it does:

• Fastens the dispenser guard to its mounting point on the dispenser assembly
• Keeps the guard aligned to prevent interference with dispenser door/flow
• Restores a secure fit if the original clip is cracked, deformed, or missing
• Common symptoms: loose or missing guard, rattling, incomplete dispensing or residue left after a cycle

• 1 dispenser guard clip

• Disconnect power to the appliance; turn off water supply if applicable
• Open access, support the guard, and release the worn clip from its tabs
• Snap the new clip fully into place, ensuring it engages all locking points
• Ensure the guard is secure and that the dispenser door/flow path is unobstructed before use