6651305790 Parts

Specs: 10-16 x 1/2 inch.

This vent housing assembly mounts in the dishwasher door to guide humid air out of the tub. A secure, sealed housing helps prevent steam leaks and moisture damage while supporting proper airflow during the dry portion of the cycle.

• Provides a sealed mounting point for the door vent
• Channels moist air out during drying to protect the door and control panel
• Helps prevent steam or moisture from escaping at the top of the door
• Common symptoms: steam or dampness at the door top, water streaks on the front panel, or visible cracks/warping in the housing

• Disconnect power at the breaker and turn off water supply before servicing
• Remove inner door panel fasteners to access the vent area
• Note orientation; transfer any gasket or retainers from the original housing if required and seat the new housing flush
• Reassemble and run a short cycle to check for leaks and proper airflow

This small clip secures the guard/shield on the dispenser assembly. Replacing a cracked or missing clip keeps the guard firmly attached and aligned so the dispenser operates properly without interference, noise, or premature product loss. What it does:

• Fastens the dispenser guard to its mounting point on the dispenser assembly
• Keeps the guard aligned to prevent interference with dispenser door/flow
• Restores a secure fit if the original clip is cracked, deformed, or missing
• Common symptoms: loose or missing guard, rattling, incomplete dispensing or residue left after a cycle

• 1 dispenser guard clip

• Disconnect power to the appliance; turn off water supply if applicable
• Open access, support the guard, and release the worn clip from its tabs
• Snap the new clip fully into place, ensuring it engages all locking points
• Ensure the guard is secure and that the dispenser door/flow path is unobstructed before use

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This diverter disc directs wash water to different spray zones during a cycle, helping ensure alternating spray patterns and thorough cleaning. A worn or damaged disc can cause poor wash performance or incorrect spray routing.

• Routes water from the sump to selected spray arms/zones
• Helps alternate spray to improve coverage and cleaning
• Worn discs may lead to weak spray, poor cleaning, or unusual cycle behavior
• Can contribute to water leaking at the diverter area if the seal interface is compromised

• Disconnect power and water before servicing
• Access is typically from the bottom; remove the toe kick and lower panel as needed
• Note the disc orientation in relation to the diverter mechanism during removal
• Inspect related components (diverter motor/shaft, seals, sump) and replace if worn

This rinse aid knob is the cap for the dishwasher's rinse aid dispenser. It seals the reservoir to prevent leaks and evaporation and provides a secure grip for refilling, helping the dispenser hold rinse aid as designed.

• Covers and seals the rinse aid reservoir opening to contain rinse aid
• Helps prevent leaks or evaporation from the dispenser
• Provides an easy-to-grip cap for removing/reinstalling during refills
• Common symptoms: missing or cracked cap, rinse aid not staying in the reservoir, leaks inside the door, increased spotting from lack of rinse aid

• Disconnect power to the dishwasher before servicing.
• Replace the cap by hand and ensure it seats fully; do not overtighten.
• After installation, run a short cycle to verify proper sealing and no leaks.

This dishwasher detergent dispenser mounts in the inner door and stores both detergent and rinse aid. It releases them at the correct time in the cycle to help deliver consistent cleaning and spot-free results.

• Holds and seals detergent/rinse aid until the control calls for release
• Opens the detergent cup during the wash cycle to dispense soap
• Helps reduce leftover detergent in the cup after a cycle
• Helps with issues like a dispenser door that won't open, soap left after the cycle, or rinse aid leaking

• Disconnect power to the dishwasher before servicing
• Remove the inner door panel to access the dispenser
• Release the locking tabs/screws, clean the sealing surface, and install the new dispenser flush with the door liner
• Reassemble the door and check for leaks before running a test cycle

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten

This dispenser water tube routes water from the inlet to the refrigerator's in-door dispenser manifold, helping ensure a steady, leak-free flow to the dispenser.

• Directs water from the supply line to the dispenser manifold
• A damaged or cracked tube can cause leaks, low/erratic dispenser flow, or air in the water line
• Replacing a leaking tube can help restore normal dispenser operation and prevent water damage

• Unplug refrigerator and shut off water supply before service
• Have a towel/container ready to catch residual water
• Note tube routing and connections; push-to-connect fittings may require firm seating for a watertight seal
• After installation, turn water on and check all joints for leaks

This cap is a small protective cover used on select appliances to close off an opening or fastener. Replacing a damaged or missing cap helps keep out debris and moisture while restoring a clean, finished appearance.

• Covers an exposed opening or fastener to protect internal components
• Helps keep out dust, moisture, and spills
• Restores a clean, finished look and prevents snags
• Replace if the original cap is cracked, missing, discolored, or won't stay seated

• Disconnect power and, if applicable, shut off water or gas before service
• Remove the old cap by pulling straight off or unthreading, as designed
• Align the new cap and press or thread into place without forcing
• Verify a secure fit before restoring power and connections

This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.

• Secures the heating element to its mounting point to keep it stable
• Maintains proper spacing from nearby components and surfaces
• Helps reduce vibration, rubbing, or rattling noises
• Replace if the original support is cracked, warped, missing, or the element appears misaligned

• Disconnect power to the appliance before servicing; allow hot components to cool
• Access the heater per your model's service information; note the original orientation and routing
• Seat the support fully and handle element leads carefully to avoid damage

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

This tub insulation shield mounts at the front/base of the dishwasher tub to cover and secure the sound-dampening insulation. It helps protect the insulation from splash and wear so the blanket stays in place for quieter operation. What it does:

• Covers and protects the tub's insulation from moisture and abrasion
• Helps keep insulation properly positioned for sound and thermal performance
• Direct replacement for a cracked, warped, or missing shield
• Typical symptoms: exposed or sagging insulation, louder operation, or difficulty fitting the toe panel

• 1 tub insulation shield

• Disconnect power and shut off the water supply before servicing
• Remove the lower toe panel/kickplate to access the shield area
• Position insulation correctly, then install the shield using the existing mounting points/hardware
• Reinstall the toe panel and test for proper fit and operation

This miniature door switch is the snap-action interlock that tells the appliance when the door is closed. Replacing a worn or sticking switch restores reliable start/stop and proper door-status sensing for safe, consistent operation. What it does:

• Acts as the latch/interlock sensor for door open/closed status
• Signals the control to allow or prevent operation based on door position
• Typical symptoms include: won't start or shows a door message, stops when the door is bumped, or light/fan behavior doesn't match door position

• 1 miniature door switch

• Disconnect power before servicing. If working on a microwave, high voltage may be present even when unplugged—properly discharge the capacitor.
• Access the latch/interlock area; note wire positions and transfer one lead at a time to the new switch.
• Use a multimeter to confirm the switch changes continuity when pressed before reassembly.

This mounting bracket holds and aligns the door interlock switch(es) so the control can accurately detect when the door is closed. Replacing a cracked or warped bracket restores reliable door recognition and consistent operation.

• Secures the door switch(es) in the correct position behind the front panel
• Maintains latch-to-switch alignment for proper door-closed detection
• Can address incorrect interior light behavior tied to door switch alignment

• Disconnect power before servicing
• Access the bracket by removing the necessary front/console panels
• Transfer existing switches and wiring to the new bracket; note wire positions
• Align and tighten fasteners; confirm switches click and door closes properly before reassembly

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power