7909446701 Parts

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

This electronic oven control board (clock/timer) is the brain of your range/oven, regulating temperature, powering the bake/broil circuits, and managing the display and keypad. Replacing it restores proper heating and responsive controls.

• Governs bake and broil circuits and maintains set temperature using oven sensor feedback
• Displays time/temperature and responds to keypad inputs
• Common failure signs: oven won't heat or start, erratic/inaccurate temps, dead or unresponsive display, repeated beeps or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board by the edges and use anti-static precautions
• Photograph/label connectors and transfer wires one at a time to the new board
• Transfer the existing keypad overlay and any brackets as needed, reinstall panel, restore power, and test bake/broil

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This is the graphic control panel overlay for the oven/range user interface. It restores legible labels and a clean appearance for touchpad buttons, helping you see and select functions accurately when the original film is worn, bubbled, or damaged. What it does

• Adheres to the control panel/touchpad to provide printed button labels and icons
• Protects the underlying keypad from spills and cleaning wear
• Helps resolve faded, peeling, or unreadable control markings
• Can improve button feel and responsiveness when the old overlay is lifting
• Restores a finished, factory look to the control panel

• One control panel graphic overlay

• Disconnect power to the appliance before starting
• Clean and dry the control panel surface thoroughly; remove all adhesive residue
• Align carefully before applying—once set, adhesive may not reposition cleanly
• Press firmly and evenly to ensure full adhesion and avoid bubbles

The Triple Radiant Surface Element is an OEM part for Frigidaire ranges and cooktops. This component features three individual electric coils contained within a single mounting unit.

The triple element provides versatile cooking options with three distinct zones that heat up rapidly and evenly. Whether simmering a sauce or boiling water, this element allows home chefs to prepare multiple recipe components simultaneously. Precise thermostat controls maintain selected temperatures accurately.

Causes of bad triple elements can include broken internal wiring from shifting or impact over time, or mineral buildup impeding heat transfer and coverage.

Symptoms of failure include:

• Only one or two coils heating up out of three
• Discoloration, cracking or pitting of the coil surfaces
• Coils that pulse or cycle excessively in lower heat settings

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

Restore a safe, finished oven door with this replacement outer glass panel. It replaces a cracked or shattered front window, protecting the door assembly and letting you see your food without exposing insulation or sharp edges. What it does:

• Forms the front/outer pane of the oven door window
• Protects door insulation and inner glass from damage
• Helps contain heat within the oven when intact
• Common symptoms: visible cracks, shattered or missing pane, loose or rattling glass

• 1 outer oven door glass panel

• Disconnect power and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; glass edges can be sharp
• Removing the door from the hinges makes service easier; support the door to prevent damage
• Transfer any trim/brackets/nameplate from the old pane and reuse existing hardware as required

Size: 8-32t x 0.500 inch. Color: Black.

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

Restore reliable top heat for broiling and browning. This replacement broil heating element brings your oven's broil function back to full strength so foods brown evenly and the broiler heats when selected.

• Provides high, direct heat from the top of the oven during the broil cycle
• Helps with top-browning in some baking/roasting modes
• Common failure signs: broiler won't heat or glow, uneven browning, visible breaks or blistering on the element
• Often tests "open" (no continuity) when failed

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, then gently pull the element forward and support the wires
• Label and transfer wires to the new element one at a time; do not allow wires to slip back into the rear cavity
• Reinstall screws, ensure secure connections, restore power, and test the broil function

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

This factory replacement plate is used on Frigidaire-made cooking appliances to cover and support a specific area of the unit. Replacing a bent or missing plate restores proper protection, alignment, and a clean, finished appearance. What it does

• Covers an opening or shields internal components as designed for the model
• Provides a stable mounting surface for adjacent parts or hardware
• Helps prevent debris intrusion and potential rattles or vibration
• Common signs it's needed: plate is missing, bent, cracked, or won't fasten securely

• 1 plate

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Retain and reuse existing screws/fasteners unless your model specifies new hardware
• Align the plate with existing holes; start screws by hand to avoid cross-threading and tighten evenly
• Verify clearances and safe operation before restoring power

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

Color: Black

This is a replacement oven range control board and clock from Frigidaire. It is the heart of the oven and is responsible for managing and monitoring all functions. It allows the user to set the oven temperature, choose baking/broiling cycles, set timers, and more. This part should last for many years, but it can be damaged by prolonged exposure to moisture or high heat.If the control board is failing or has failed, the oven may be inoperable, or it may experience erratic or erroneous operation. A multimeter test is needed to determine if the problem is the control board, though. This part does not include the overlay, which is needed to capture user inputs. To replace the control board and clock, users will need to unplug the oven. Remove the rear access panel of the oven, locate the wiring harnesses, then disconnect them. Remove the mounting screws and then the old board. Install the new board by reversing these steps. This control board is a genuine OEM part and is sold individually. It is compatible with Kenmore ovens.

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place