970-688530 Parts

This dryer thermostat monitors internal air temperature and opens/closes the heater circuit to keep drying safe and consistent. Replacing a weak or failed thermostat restores proper heat and helps prevent overheating or nuisance shutdowns. What it does:

• Senses exhaust/heater housing temperature and switches the heating circuit based on temperature
• Helps maintain target drying temperatures for consistent performance
• Provides over-temperature protection by opening the circuit if heat rises too high
• Common symptoms include no heat or weak heat, long dry times, heat cutting out mid-cycle, or the dryer running hotter than normal

• 1 thermostat

• Disconnect power before servicing; heating components can be live and hot
• Access location varies by model; typically mounted on the heater or blower housing behind a rear or front panel
• Transfer wires from the old thermostat to the new one one-at-a-time and secure firmly; ensure the mounting surface is clean and flat
• After replacement, check and clear the venting/duct for proper airflow to prevent repeat failures

The Drive Motor is an OEM part for Frigidaire washing machines. This motor powers the drum's rotation during both the wash and spin cycles. It ensures that the drum agitates and spins correctly, allowing for effective cleaning and rinsing of laundry.

Over time, the drive motor can fail due to regular wear and tear, electrical issues, or overloading the washing machine.  

Symptoms of a bad drive motor include:

• The drum not spinning or agitating
• Unusual noises or humming sounds during operation
• The washing machine stopping mid-cycle
• Burning smells coming from the motor area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This O-Ring creates a tight, leak-resistant seal between appliance components. Replacing a worn or flattened ring restores proper sealing, helps stop drips at the joint, and protects nearby parts from moisture and mineral residue.

• Provides a compression seal between fittings, housings, or tubes
• Helps prevent water leaks and loss of pressure at the connection
• Common signs of failure: moisture or residue around the joint, visible cracks/flattening, leaks after reassembly
• Regular wear, heat, chemicals, or age can harden or deform the ring

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; lightly lubricate the new O-ring with food-grade silicone grease
• Seat evenly without twisting or pinching; reassemble and check for leaks

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

The Deli Drawer Cover Frame is an OEM part for Frigidaire refrigerators. It serves as the frame that holds and supports the deli drawer cover, ensuring a secure fit and smooth operation. The cover frame is designed to maintain the proper positioning of the deli drawer cover, allowing for easy access to stored items while preserving the overall organization and appearance of the refrigerator interior.

Symptoms of a bad Deli Drawer Cover Frame include:
• Difficulty opening or closing the deli drawer
• Loose or misaligned deli drawer cover
• Cracks, breaks, or visible damage to the cover frame
• Interference with other refrigerator components due to improper fitment

Causes of a damaged or malfunctioning cover frame can include accidental impact, excessive force applied during use, or general wear and tear over time. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM replacement part for Frigidaire appliances. This screw is used to securely fasten components, such as panels, brackets, or internal parts, ensuring the appliance remains stable and functions correctly. Its precise design ensures a snug fit and reliable performance in the designated area of the appliance.

Over time, screws can become stripped, corroded, or loosened due to vibrations, frequent use, or environmental factors. A damaged or missing screw may lead to instability, misaligned components, or operational issues with the appliance.

Symptoms of a bad or missing screw include:

• Loose or misaligned panels or components
• Rattling or unusual noises during operation
• Difficulty in securing parts during repairs or adjustments
• Parts becoming detached or unstable

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This dryer timer is the cycle control that advances your dryer through Timed and Auto Dry settings. Replacing a failed timer restores proper cycle progression, start/stop, and end-of-cycle shutoff.

• Advances the cam and internal contacts to move the dryer through heat, motor, and cool-down steps
• Governs run time on Timed Dry and Auto Dry cycles
• Routes power to the correct circuits in sequence; a failed timer may not advance or may stop early
• Common symptoms include timer knob not moving, dryer running indefinitely, or not starting on certain settings

• Disconnect power; for gas models, also shut off gas
• Remove knob/dial, open the console, and unmount the timer
• Label or photograph wiring; transfer wires one at a time to the new timer
• Reassemble and test both a Timed Dry and an Auto Dry cycle

Color: white. Measures about 1-1/2 inches in diameter.

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Color: White. Used to cover the hinge bearing hole.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This motor control board regulates the washer's drive motor, managing speed and direction for tumble and spin cycles. Replacing a failed board helps restore drum movement and consistent cycle performance when the motor no longer responds. What it does:

• Controls drive motor speed and direction during wash and spin cycles
• Executes motor start/stop commands from the main control
• Failure can cause no spin, no tumble, or intermittent drum movement
• Trigger motor-related fault codes on some models

• Includes: 1 motor control board

• Disconnect power before servicing; observe ESD precautions when handling the board
• Access the control board per your model's service manual (typically in the base or rear cabinet area)
• Transfer wire connectors one at a time to the new board; ensure each is fully seated and latched
• Mount securely, reassemble, and run a diagnostic or spin test to verify motor operation

For a complete drum bearing and shaft kit order 5303281153.

The Drive Motor is an OEM part for Frigidaire washing machines. This component is essential for powering the washing machine's drum, enabling it to agitate and spin during the wash and rinse cycles. It ensures that clothes are thoroughly cleaned and properly spun dry.

Common causes of a bad drive motor include wear and tear from frequent use, overheating due to heavy loads, electrical issues such as power surges, and physical damage from impact or mishandling.

Symptoms of a bad drive motor include:

• The washing machine not spinning or agitating
• Loud, unusual noises during operation
• The washer not starting or stopping mid-cycle
• Burning smell or visible signs of motor overheating

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Size: 3/4 inch od x 1/4 inch id.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.