Thermador Memcw271es Parts

The Sensor is an OEM replacement part for Bosch ranges. It monitors conditions inside the oven compartment such as temperature and diagnosing faults. 

Symptoms of a bad sensor include:

• The oven not heating or cooking unevenly
• Inaccurate temperature readings displayed  
• Erratic or unpredictable ignition/operation  
• Error codes appearing related to sensor faults

Causes of failure can be normal wear over time from high heat exposure, accidental damage compromising sensor integrity, or intrusion of liquids or debris confusing readings.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore ranges.

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This dishwasher water sensor monitors wash-water conditions so the control can adjust cycle time, rinses, and heating for consistent performance. Replace a failed sensor to restore reliable cleaning results and proper automatic cycle adjustments. What it does

• Detects water conditions during the wash cycle and reports to the control
• Helps the dishwasher optimize cycle length, rinses, and energy use
• Common symptoms: unusually long or short cycles, inconsistent cleaning, or sensor-related error messages
• Trigger erratic cycle behavior when the sensor is faulty or contaminated

• One sensor assembly

• Disconnect power and turn off water before servicing
• Access is typically from the underside; place a towel or pan to catch residual water
• Transfer/seat the seal properly if present; fully engage the locking tabs and reconnect the harness
• After installation, run a quick cycle and check for leaks and proper operation

The Fuse is an OEM component specifically designed for Bosch microwaves. It protects internal circuits and components from power surges or overloads that could cause damage. Proper functioning defends the appliance from electrical hazards.

Symptoms of a blown fuse can involve the microwave failing to power on or function after prior episodes of tripped internal safety mechanisms. Repeated events increase replacement needs.

Causes of a bad fuse involve normal wear under prolonged power cycling. However, significant power spikes pose greater fuse risks necessitating timely changes to warranty circuit integrity.  

Symptoms of a bad fuse include:

• Microwave fails to turn on or shows no response to controls
• Lightbulb does not illuminate during heating cycles
• Tripped circuit breakers occur frequently

This OEM Bosch part is also compatible with some Thermador, Blomberg, and Miele microwaves. Replace faulty fuses to restore appliance usability and safety.
 

This convection fan motor drives the oven's internal fan to circulate hot air during convection cooking. Replacing a weak or seized motor restores proper airflow for more even heating, reliable temperatures, and consistent baking and roasting results.

• Powers the convection fan to move heated air across racks for even cooking
• Helps maintain stable cavity temperature and quicker recovery after door openings
• Common symptoms of a failing motor: fan won't turn, intermittent start/stop, loud squeal or grinding, uneven baking/roasting, or a fan-related error

• Disconnect power at the breaker before servicing
• Access from the rear of the unit or through the oven cavity (model dependent); remove the appropriate panel to reach the motor
• Note wire positions and motor orientation; transfer any brackets, grommets, or screws from the original if needed
• Ensure the fan blade spins freely and is properly seated before reassembly

This micro switch is a small, fast-acting on/off switch tripped by a mechanical lever or float to send a signal to the control. Replacing a worn microswitch restores accurate sensing so the appliance starts, stops, and runs when it should. What it does

• Senses the position of a linked mechanism (lever, float, latch) and opens/closes an electrical circuit
• Helps the control enable or disable functions only when conditions are correct
• Failure symptoms include intermittent operation, cycles that won't start, or a unit that keeps running until power is removed

• Disconnect power and, if applicable, shut off water before servicing
• Access the switch and note actuator orientation and terminal layout
• Move wires to the new switch one at a time to maintain correct placement; ensure tight connections
• Manually actuate the mechanism to ensure a positive "click" and proper operation before reassembly

This control module is the appliance's main electronic control board. It interprets inputs and energizes components to run the correct sequences, restoring reliable operation when the original board is unresponsive, intermittent, or damaged. What it does

• Coordinates timing and operation of motors, valves, heaters, and other loads
• Monitors inputs from switches and sensors to make decisions
• Distributes power and controls relays/outputs to components
• Common failure symptoms: won't start, controls unresponsive or erratic, stops mid-cycle, or shows error codes

• 1 control module

• Disconnect power before servicing; electronic boards can carry residual charge
• Use ESD precautions; handle the board by the edges and avoid touching components
• Document wiring; move connectors one at a time and ensure they are fully seated and keyed correctly
• Secure the board and any ground straps; reassemble, restore power, and run the model's service/diagnostic test if applicable

This factory fixing kit provides the mounting hardware needed to secure the applicable component or panel on your appliance. Replacing worn or missing fasteners restores proper alignment and a solid, rattle-free installation.

• Secures panels, brackets, or trim to the appliance chassis or door
• Helps prevent shifting, vibration, and rattling during operation
• Restores correct alignment and fit when hardware is missing or stripped
• Useful during initial installation or when re-installing serviced parts

• Disconnect electrical power; if your appliance is plumbed, shut off water before servicing
• Follow your model's installation/service instructions for exact hardware locations and orientation
• Tighten hardware evenly; do not overtighten to avoid damaging plastic or sheet metal
• Verify alignment and smooth operation before restoring power and/or water

This door latch secures the appliance door and helps enable normal operation by keeping the door closed and latched during cycles. Replacing a worn or broken latch restores proper door engagement and reliable start/lock behavior. What it does:

• Secures the door closed so the appliance can run and complete cycles
• Engages with the strike to maintain a tight, consistent seal during operation
• Helps the control detect a closed/locked door and permit cycle start
• Commonly replaced when the door won't stay closed, won't lock, or the unit won't start

• One replacement door latch

• Disconnect power and water before beginning any repair
• Access may require removing the inner door panel or front trim—keep fasteners organized
• Verify alignment of the latch and strike before reassembly to ensure proper engagement
• If the latch has electrical connectors, reconnect securely and avoid pinching wires

This heating element restores proper water temperature and drying performance in your dishwasher. When the original fails, cycles may run long and dishes can come out wet; replacing it brings back consistent, efficient cleaning results. What it does:

• Heats wash and rinse water to help dissolve detergent and remove soils
• Raises final rinse temperature to improve drying performance
• Works with the control and sensors to maintain target temperatures
• Common symptoms include water not heating, poor drying, extended cycles, or a heating-related fault

• 1 heating element

• Disconnect power at the breaker and shut off water before servicing
• Pull the dishwasher and/or remove the toe panel as needed to access the heater wiring and mounts
• Note wire positions and make secure, clean terminal connections
• After reassembly, run a test cycle and inspect for leaks and proper heating

This fan blower wheel circulates air inside the appliance to help maintain even temperatures and proper cooling. Replacing a worn or broken fan restores airflow and helps the appliance reach set temperatures consistently. What it does:

• Moves air through the evaporator/condenser area to support cooling and defrost cycles
• Helps prevent hot or cold spots by circulating conditioned air
• Commonly related to reduced cooling, noisy operation, or no airflow from the vents
• Can be a root cause of frost buildup or temperature fluctuations when failed

• Disconnect power before starting any repair to avoid electrical shock
• Access may require removing interior panels or the evaporator/condenser cover
• Inspect the mounting and motor for wear; replace the fan only if it matches the OEM shape and fit

This replacement cover protects internal components and restores the proper fit and finish of the original assembly. It secures nearby parts and helps prevent debris from entering sensitive areas. What it does:

• Covers and shields internal components from dirt and loose debris
• Secures the assembly and helps reduce vibration or rattling
• Replaces cracked, broken or missing covers that cause poor fit or unsecured parts
• Restores original appearance where the factory cover is damaged or lost

• Power off and unplug the appliance (or shut off circuit) before starting work
• Remove necessary access panels or screws to reach the cover; retain hardware for reassembly
• Align cover before fastening; do not force or over-tighten screws to avoid damage

Replacement refrigerator glass shelf that restores stable, easy-to-clean storage inside your fridge. Replaces a cracked, chipped or missing shelf so you can safely store food and containers while keeping the interior organized. What it does

• Provides a flat, durable surface for storing food, containers and small appliances.
• Replaces shelves that are cracked, chipped, broken or missing.
• Helps contain spills and makes cleanup faster with a smooth, wipeable surface.
• Fits into existing shelf rails/grooves to restore usable storage space.

• Unplug the appliance or disconnect power before installing and remove all items from the shelf area.
• Lift out the old shelf by sliding it out of the support grooves; position the new shelf into the same rails until it seats securely.
• Handle glass carefully — wear cut-resistant gloves and place the shelf on a padded surface during installation.
• If shelf supports, clips or rails are damaged, replace them before use and follow the appliance manufacturer's instructions.

User interface control panel that provides the buttons and display used to select cycles and view appliance status. Replaces a faulty control panel to restore responsive controls and clear cycle/status feedback. What it does:

• Registers user input from the touchpad/buttons; may fail if buttons are unresponsive or intermittent.
• Displays cycle progress and status indicators; can show blank, garbled, or missing segments when faulty.
• Sends user commands to the appliance control system; failure can prevent cycles from starting or changing.
• Common symptom linkage: unresponsive controls, no display, incorrect cycle selection, or persistent status/errors.

• Always disconnect power (unplug or shut off breaker) before servicing the appliance.
• Handle the display/overlay and ribbon/wire connectors carefully to avoid damage.
• Remove and replace the console using correct fasteners; ensure all connectors are fully seated.

This socket is an electrical connector used to join wiring or plug-in components, restoring a secure connection for reliable appliance operation. It replaces a worn or damaged socket to help prevent intermittent power or component failure. What it does:

• Provides a secure electrical connection between wiring and the appliance component
• Restores proper contact when a loose, corroded, or broken socket causes intermittent operation
• Helps prevent arcing or poor connections that can lead to component failure
• Used where a plug-in or push-fit electrical connection is required

• One socket

• Disconnect power to the appliance before inspecting or replacing the socket
• Replace only with the exact socket type specified for your appliance